GDM - E36 Drift/Race Project

[Garett 103]

You reckon I've done no measuring.... I haven't lol

 

The dish I've come up with it -16 

Edited September 12, 2016 by Garett

[polley 916]

you seem to have a lot of question marks lol...

 

if you have the head off, cc it with a spark plug in it. you will often find they are a bit different than what you might find on the internet.

[Garett 103]

Not yet, sounds like a good idea

[Garett 103]

Some good things have arrived, still a lot to come

[Garett 103]

Ok so used this handy calculator found here... http://www.csgnetwork.com/compcalc.html

Going to go with -18 dish pistons which should get me close to 9:1

The S50b32 cylinder head i brought was missing a lifter, ive placed that on order along with a 2,75 shim and 2 oil squirters that the goat stood on and destroyed

 

[M3AN 4015]

10 minutes ago, Garett said:

...that the goat stood on and destroyed...

Hate it when that happens.

[Garett 103]

Yeah hes a payne in the ass, anyone want a goat... stands on bonnets and chases people i'm sure he'd make a good stew for the right person

[Garett 103]

Wheres the best place to get a single piece driveshaft for my car??

Google says http://www.driveinn.co.nz/driveshafts/4550008919 in nz may make one and https://www.vividracing.com/catalog/driveshaft-shop-chromoly-driveshaft-bolt-rear-flange-9599-p-55683.html if want to buy one, anyone know of any others??

 

[jom 96]

4 minutes ago, Garett said:

Yeah hes a payne in the ass, anyone want a goat... stands on bonnets and chases people i'm sure he'd make a good stew for the right person

My sister had a goat that would butt at it's own reflection. Cost me (and others!) a door skin until I learned to drive through all the dirty puddles on the way to see her.

[WYZEUP 281]

Dont use a single piece drive shaft bro, after speaking to the guy at ANL you get lots of vibration from them and you loose a lot of strength so have to use a larger diameter pipe to get the same strength and stop the sagging. But if you want to go that way go and speak to ANL and have it custom made

[E30-323ti 66]

Speaking from my experience also, do not go for a 1pc driveshaft.

I went through 4 variations (diameter / thickness) to get the vibration out of mine to no avail.
Went back to a 2pc and is smooth as silk.

[richard 384]

23 hours ago, Garett said:

Wheres the best place to get a single piece driveshaft for my car??

Google says http://www.driveinn.co.nz/driveshafts/4550008919 in nz may make one and https://www.vividracing.com/catalog/driveshaft-shop-chromoly-driveshaft-bolt-rear-flange-9599-p-55683.html if want to buy one, anyone know of any others??

 

I've been looking at this one

http://www.evasivemotorsports.com/mm5/merchant.mvc?Screen=PROD&Product_Code=DRIVESHAFT-BMWSH2-CV-C&Store_Code=EM&search=bmw+e36+carbon+driveshaft&offset=&filter_cat=&PowerSearch_Begin_Only=&sort=&range_low=&range_high

[richard 384]

http://www.evasivemotorsports.com/mm5/merchant.mvc?Screen=PROD&Product_Code=DRIVESHAFT-BMWSH2-CV-C&Store_Code=EM&search=bmw+e36+carbon+driveshaft&offset=&filter_cat=&PowerSearch_Begin_Only=&sort=&range_low=&range_high

go to this link at search bmw e36 driveshaft.

don't know why its not coming up in the link.

Edited September 22, 2016 by richard

[Garett 103]

Cool thanks guys i'm on the fence about it all right now. 

After talking to a few people it doesn't look like i'm going to be able make my target hp of around 800-850 well reliable hp anyway as it will cost a stupid amount upgrading gearbox, driveshaft, diff, axles, clutch to be able to handle prolonged use of it
As sad as it is i'm going to have to admit defeat and just try see what happens at Dyno time with the new mods to the M3 engine only and see if there are any loose links that need attention then

 

 

 

[Garett 103]

27 minutes ago, richard said:

http://www.evasivemotorsports.com

go to this link at search bmw e36 driveshaft.

don't know why its not coming up in the link.

 

Cheers for the link, never heard of them ill add it to my favs

[Garett 103]

5 hours ago, E30-323ti said:

Speaking from my experience also, do not go for a 1pc driveshaft.

I went through 4 variations (diameter / thickness) to get the vibration out of mine to no avail.
Went back to a 2pc and is smooth as silk.

 

I did read alot about this issue, cheers for the heads up!

[Garett 103]

Has anyone got a light vented bonnet they want to sell, the factory one is pretty heavy and looking to swap it out.

[richard 384]

8 minutes ago, Garett said:

Has anyone got a light vented bonnet they want to sell, the factory one is pretty heavy and looking to swap it out.

I'm going to have a go at making carbon fiber doors and bonnet straight copy

Edited September 22, 2016 by richard

[Garett 103]

2 minutes ago, richard said:

I'm going to have a go at making carbon fiber doors and bonnet straight copy

 

Id like to see how the bonnet turns out...

 

[No name user 379]

23 minutes ago, Garett said:

Cool thanks guys i'm on the fence about it all right now. 

After talking to a few people it doesn't look like i'm going to be able make my target hp of around 800-850 well reliable hp anyway as it will cost a stupid amount upgrading gearbox, driveshaft, diff, axles, clutch to be able to handle prolonged use of it
As sad as it is i'm going to have to admit defeat and just try see what happens at Dyno time with the new mods to the M3 engine only and see if there are any loose links that need attention then

 

 

23 minutes ago, Garett said:

 

 

 

[HaNs 226]

14 hours ago, richard said:

I'm going to have a go at making carbon fiber doors and bonnet straight copy

http://www.pesch.cz/en/category/bmw?page=2&radit=0 

 

Im keen to do a order if you are?

[richard 384]

5 hours ago, HaNs said:

http://www.pesch.cz/en/category/bmw?page=2&radit=0 

 

Im keen to do a order if you are?

I'm keen on the doors and bonnet if the shipping price right .

[Garett 103]

Man that stuff is a rough as guts but i guess you get what ya pay for ill take one of these http://www.pesch.cz/en/product/fiberglass-hood-bmw-e36-coupe

and maybe one of theese http://www.pesch.cz/en/product/bmw-e36-front-bumper-fiberglass lol

 

 

 

 

Edited September 23, 2016 by Garett

[richard 384]

same shop

[Garett 103]

This is a interesting read http://www.bimmerforums.com/forum/archive/index.php/t-2132218.html

Edited September 23, 2016 by Garett