Jump to content

hotwire

Race Series Competitors
  • Content Count

    3860
  • Joined

  • Last visited

  • Days Won

    3

hotwire last won the day on March 25 2020

hotwire had the most liked content!

Community Reputation

352 Excellent

About hotwire

  • Rank
    Grant
  • Birthday 12/06/1963

Previous Fields

  • Name
    Grant M
  • Location
    Big Smoke -Te Awamutu
  • Car
    99 E39 525i
  • Car 2
    78 E12 520i
  • Race Car
    E30 320i
  • Race Car Number
    #63

Contact Methods

  • Website URL
    http://
  • ICQ
    0

Profile Information

  • Gender
    Male

Recent Profile Visitors

7814 profile views
  1. As Dan says - very straight forward BUT only if you have ALL the parts. It is practically plug & play You require: Gearbox - complete with shifter linkage/stick & mounting bracket Front section of driveshaft - to suit G260 E30 Clutch plate, pressure plate, release bearing, flywheel & circular shim plate. All associated bolts. As Dan says - insert a spigot bearing Master cyl, slave cyl, reservior/bracket, clutch line & hoses - pressure & reservior to master cyl Manual pedals & the matching longer bolt or a complete pedal box. It is easier to change the pedals rather than swapping the whole box. Remove the auto pedal & insert the two pedals with the longer bolt. There is a perferated panel on the bulkhead - push this out & mount the master cyl to the pedal box (pre existing mounting holes) The clutch line pipe clips into pre existing clips along the bulkhead & down to a mounting point on the L/H inner guard/rail - where it connects to the hose to the slave Reservior bracket mounts to the battery tray, hose leads through an existing hole in the bulkhead onto the master cyl. Remove the auto shifter assy. Underneath is remove the auto trans & cooler lines, fit a new spigot bearing into the crank, fit the clutch, gearbox & either swap the driveshaft or split the existing & replace the front section (rear half is the same for all). Make sure your box mounts, giubo, hanger bearing & u joints are all good - replace if not. Also shifter linkage bushes, they are best replaced anyway. You need to bridge the inhibitor switch wiring in the plug that connected to the shifter. Green /yellow to green /black for start & green /yellow to blue/white for reverse lights. Note: if the G260 came from an E30 then all above applies. If it came from an E34 then several parts need swapping. I can fill you in on that if need be.
  2. Yep seen that. pretty cool!
  3. I have the NT644 & confirmed it will not reset the service schedule (inspection anyway) on analogue system in the E30 but does read codes & show current data. It shows as having done reset but doesn't action. That said, nor does the much more elaborate Autel tablet scanner at work. I need to use the older Hanatech work scanner to do so.
  4. ^^^^^^^^^ This is an eleven year old thread. What is the point in dredging this up?
  5. I would apply a Rust Converter to treat it if is only surface rust.
  6. We have a customer code at work to quote to Repco for any parts we ( mean I ) may require - since we are classified as an essential business. Repco Te Awamutu is closed though, call forwarded to Hamilton & parts couriered to work. Our other parts suppliers are available for trade too
  7. hotwire

    Quick rant thread.

    Yep I'm at that stage too!
  8. Nup you can't sorry. You will need a total monitor retrofit which will require rear mount radio tuner, antenna amplifier + video module or nav unit (for screen graphics) & the harness assy. The 16:9 monitor is just a dumby (apart from the tape deck) - all the modules are remote to it in the rear of the vehicle. Also - is the 16:9 monitor a specific X5 unit? Many are sold as fitting E38/39 & 53. The X5 unit is different as the screen pixels are set for the different viewing angle in the X5 So, either a lot of work & cost to retrofit the 16:9 or - go back to original radio (will plug into existing plug) or another Chinavin unit.
  9. ^^^^ got a set of Factory sport option Billy's for the E12 a couple of years back out of BMW AG
  10. Yep agree to all above. I did everything including thermostat housing in one hit on mine. Fit & forget. Radiator is the only part not replaced as yet.
  11. You should scan it with live data to see what is happening. Internal module faults can cause all kinds of rogue fault codes. I would bet the module at fault.
  12. No better than the C180 Benz at work at the minute. 117000km, totally clean well serviced engine & the timing chain has jumped the exhaust cam sprocket 1/4 turn. Teeth on both cam sprockets severely worn. To add salt to the wound, Benz want $4.5k for parts to repair!
  13. Yes but they only assembled. The problem is the design santa - get a 6 cyl version - a much better car
  14. Those ignition coils very rarely fail, even at age. Ironically they are usually the first thing to get blamed for poor running. But - the new one is shiny ?
  15. Yea and the 3 are up near retail to offset the 1 free offer. in this case - 1 at retail to offset the 1/2 price of the second. Marketing 101
×
×
  • Create New...