Search the Community

Showing results for tags 'engine rebuild'.



More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


Forums

  • General
    • New Member Introductions
    • General Discussion
    • News
    • Off-Topic
    • Other European Cars
  • BMW Race Series
    • Race Series - General Discussion
    • Race Series - Technical
  • Track Days
    • Track Day Events
    • Vehicle Setup
  • Technical
    • Performance
    • Maintenance
    • Brakes, Suspension & Steering
    • Wheels & Tyres
    • Appearance
    • Audio & In Car Entertainment
    • Forced Induction & Performance Tuning
    • Electrical system
    • Interior
    • Engineering/Fabrication
  • Rides
    • Showroom
    • Videos & Sound
    • Projects
  • Marketplace
    • For Sale
    • Want to buy
    • Sponsors & Preferential Rates.
    • TradeMe discussions
  • bimmersport.co.nz
    • Forum Help and Support

Calendars

  • Bimmersport Community Calendar

Name


Location


Car


Mods List


Car 2


Car 3


Race Car


Race Car Number

Found 1 result

  1. Bought my first BMW in early 2015, it was a fairly standard 320i that was converted to manual and was put on HR springs and KYB shocks with a set of replica volk wheels Used this car as my daily for about a year and did a few things to it, had plans for it but at the time i was driving it every day and it served its purpose well Put some TD144s on it had a problem with the tyres on them changed them down a sidewall thickness and put a bit of stretch and they worked well also put on a Grip Royal steering wheel on to replace the factory wheel it had and that was about the extent of the "mods" i had done to the car until the front cross member gave out on me and broke the small tab that bolts the sway bar bracket on. So at that point i decided to it was time for a M20B25 upgrade "might as well change the engine while i'm fixing this front cross member" I said and from there things spiralled out of control and what started as a 2.5 swap has now turned into a M20B25 stroker turbo build so the motor was pulled stripped everything out of the engine bay and shaved off unnecessary brackets for a nice clean look paint and rust work (leaking brake master i believe) were done at Riverlea Panel and Paint Braided clutch, fuel and brake lines being installed (some shown) Brand new Fenix radiator E36 steering rack and custom shaft wanted to go Z3 but best option at the time was e36 so went with that During all of that i picked up a used M20B25 from Auckland came from a 89 vert with 180000 ks on it but engine ran fine so guess it made sense to rebuild it lol In went a 2.7 Stroker kit 2.7 crank 135mm rods M50???? pistons can't remember what they came from now engine was sent to Cambridge Engine Services for cleaning and checking all was good so in it all went using OEM bearings, rings and gaskets down the bottom Crank scraper and sump baffle were fitted (pain in the ass with two gaskets and very tight baffle to install) Head was ported and polished by Jim at same shop new valve guides and stainless steal valves installed Head was planed just a smidge Bolted together with an Elring HG (2mm) and cap screws head fitted with brand new valve springs and retainers, a reground 272 cam, HD rockers and oversized eccentrics brand new water pump fitted Just currently needing a timing belt and tensioner which i'll pick up this week couldn't resist test fitting the manifolds and turbo when it was all torqued down lol won't be running it with the turbo straight away as it will be easier to run the motor in on the factory ECU that way i'll have the cam run in and the rings will seal really well before boost is added which will be courtesy of a Sinco manifold, front facing plenum and Master Power MPR-494 in the meantime tho just going to be using the standard intake and exhaust , intake fitted with custom fuel rail to run -6 fittings and braided lines which the whole car has been converted to (pics to come) ^ pic of the lines coming into the engine bay unsecured atm brake and clutch lines also being changed to braided lines all bushes being changed to revshift aftermarket ones offset bushes above yet to do the diff mount bush as I'm looking for a medium case diff at the moment and will be twin mounting it underneath the car shortly. E36 adapter shaft with solid aluminium centre Motor and gearbox will be going in shortly with revshift gearbox mounts and Range Rover v8 engine mounts using a spec stage 3, 6 puk clutch and lightened factory flywheel shipped for $700 from Evan at SpeedFactor will definitely be able to handle the power I'm expecting to make will be picking up some seat rails for these in the next few weeks and bolting them in (can't wait these seats are awesome) will be updating this build very soon for now peace