bretta
Members-
Content Count
40 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout bretta
-
Rank
1st Gear
- Birthday 11/16/1960
Previous Fields
-
Name
Brett Agnew
-
Location
Howick, Auckland
-
Car
'02 VW Passat V5
-
Car 2
'04 Honda Civic VT-X
Contact Methods
-
Website URL
http://homepages.woosh.co.nz/bagnew/
-
ICQ
0
Profile Information
-
Gender
Male
-
Thanks Glenn - I'll pass on your details. Cheers
-
Cheers - I found out he has been quoted $198 + GST each!
-
Yet another friend is having troubles with his e46 320 mspec. He has been told he needs 6 new ignition coils as his car had oil leak in hte rocker cover, and damaged all 6 coils. Does this sound plausible? He just wants to check to see if he is being fed a line. Thanks in advance, Brett
-
Thanks for the advice - I'll try to talk my friend into joining this, and he can get the info first hand.
-
Hi. A friend has asked if it is ok to run his 2008 e70 X5 diesel without a particle filter in the exhaust. Apparently there is a 6 week wait until they arrive in the country, as a lot have started getting clogged. He has been advised by a Ferrari owner that a lot of his friends run their cars without the particle filter. Any thoughts? Thanks in advance. Brett.
-
Does anyone in (south) Auckland have a right hand side sun visor in gray that they want to sell? Cheers, Brett
-
Yes - they're the same. The main trouble is getting the tension pully across far enough to release enough pressure. I'm looking at having to take the radiator and front end off to get enough room to do this. I can't get a socket/power bar on, and the ring spanner has too much of an angle to stay on. The open end spanner is slipping off. I may just have to get a mobile mechanic to come put it on for me! Cheers.(And it is probably really easy with the specialised VW tool!)
-
I'm trying to fit a new serpentine belt to a 2002 VW Passat B5.5 V5. I have managed to get the belt on after fitting a new tensioner pulley, but can't get it over the last pulley (Alternator). I have released as much tension on the pulley as I can, and have moved the alternator as much as I can, but am about 1/4" to 1/2" away from getting the belt on. I would be grateful for ideas. Many thanks, Brett
-
Anyone around Auckland have one of these lying around in reasonable condition? I need to replace one to get warrant. Many thanks
-
My '97 323 has (sometimes) started to run rough after the engine has been running fore a while - anywhere from 3/4 hour to 2 hours. It feels like it is running on only 3 or 4 cylinders, loses power, idles roughly. If the motor is switched off for anything from 5 to 15 minutes, it quite often starts and runs ok, again for about 3/4 hour or more (I am generally back home by then). I am perplexed with the fact that if left for 5 minutes, everything runs fine for sometime before problem reappears, if at all. Any ideas of what I can check? Would plugs or coil packs the primary suspect? Could it be a fuel issue? All fluid levels are ok, Oil filter, Air Filter, plugs done at last oil service - only just down to 1 green light now. Cheers, Brett
-
Cheers - I appreciate teh help.
-
Thanks Glenn - this makes the 3rd over the past 6 years!
-
Hi I have a '98 Maxima that has a problem with the charging light staying on until the engine gets to about 3000 - 3500 rpm before going off. Then it sometimes stays off, but sometimes comes on until the revs get up again. I have checked the belt, and it appears to be tensioned ok. The Battery is coming up about 2 years old, and was a slightly heavier duty than the standard (but still a recommended type). The altenator was replaced (again) about 4 years ago. Can anyone point me to a possible problem in either battery or altenator, or something else? Thanks in advance Brett
-
Check out the AA - they were looking at an "advanced" driving skills training programme
-
Thanks - that makes more sense than CV joint