IIIRII

So whats a realistic power / torque for the factory clutch on a manual 135i ? MHD stage 1 and 2 have 2 options 1 360/520 1+ 390/600 2 380/560 2+ 420/650 So , the way i read it stage 2 makes less torque , so theroretically less hard on the clutch ... Anyone with real world experience got any thoughts ?

I have a set of Ruff adjustable top plates to suit e36 Part # BW-FSM-02 E36 / M3 L / MZ3 Brand new $225

Hi Thanks, I think you have misunderstood the question The car doesnt run a bmw diff. Is there a difference in rear axle length between 4 and 6 cylinder E30's Thanks '

Apologies if the answer is already here somewhere obvious and I have missed it. Are E30 / 36 ti axles different lengths between the 4 and six cylinder engines ? As in I think 316 318 have a small case diff and the 320 323 325 has a medium case, therefore the axles should be slightly shorter ??? Is there a shorter axle again ? like from a large case diff , that will fit the e30 e36 ti hub Hopefully that makes sence Thanks

I have a 318tiCompact pretty much completely stripped It has new trailing arm bushes, new rear wheel bearing, ally subframe bushes, The car is at the point where its about to have the cage done and all the welding finished. At this stage it has been turreted in the rear and has a cromoly frame for holding a ma 70 supra diff centre, on spuds tacked into position. You could just weld it all in and make some flange adaptors and job done. Rego on hold, it was an auto. It would be real seay to convert it back to a factory diff centre just by putting another rear subframe beam into it. Its rolling / I have all the glass and doors etc: to put it back together, I did cut some of the wiring loom to get it out but its pretty much intact (i wasnt going to use it as its overkill) It was a complete driveable car, I still have all the bits needed to make it a road legal race car etc: Im wanting $800 for thje rolling shell, without the diff centre. All part to go with it I have collected are negotiable to the person who buys it Open ma70 diff centre 4.55 or 5.3 ratio Including screw in studs 50mm L to convert the hubs to stud Adjustable front strut tops Aftermarket wiring loom Springs to suit the shocks (shocks are not for sale) Adjustable Pedal box Some other bits ive probably forgotten about PM Me a contact number Dont ask for any individual parts as the person who buys the shell has first option so that needs to go first. Cars in Franklin Area Ak

Hi, I actually need the dimension, as in "the distance across the hubs = xx mm" Which is why I titled the thread as such.

I have a tidy E36ti I bought as a donor for a race car, but then thought it was too tidy to put on gravel so found a less tidy auto that im using, so this one is for sale. 143k Blue Manual Very tidy genuine original well looked after car 96 i think M42 I dare say itll end up on tardme, if I can bring myself to donate the $50 it costs to list it. Drivers air bag, There must be different models of ti's This has drivers airbog No sun roof No air con Almost new tires $4250 Pm me for pics or viewing etc:

Anyone happen to know hub face to hub face across the rear of a e30 / e36 ti ? Im looking at rear end swaps

E30 Coupe Passengers Door Doesnt need to be tidy or perfect

Ok Cheers for that I should have had a good look at the m3 on its roof half way up bright road the other day .

Ah, So compacts have E30 rear ends. And the e36 car / coupe rear end will bolt into both the e30 coupe and the e36 compact ?

Ive been researching a few options for a rally car, and was thinking maybe e 30 coupe or e36 compact. I was under the impression e36's had a different rear end setup than e30's, but I found a build thread on the pommy rally forums where a guy is building a e36 compact, but it has a trailing arm setup like the e30. Was there a transition date or cross over period from 1 type to the other or is this just a northern hemispherre thing ? Are ALL NZ e36 compacts wishbone rears ? Ta

Im after a E30 2 door as a donor for my next buld Literally a rolling shell that can still be rego'd would be ideal Needs windscreen but no interior no motor no gearbox Just on the offchance someone has or knows of somethig North island only Ta

Hey buddy I wasnt bashing it , I said IMO the design was wrong and I doubt it would do anything. I also explained why. Say whatever you like , I have explained why it is wrong , and it is , so get over it.

So now >?? Show me a picture of the ACS one ... Hey like I said Im not trying to undermine what you have made , Im saying in my opinion it wouldnt do anything ..