marquis

More power/boost (steve murch turbo tickle-ups, manifold, external gate, new exhaust)

Saw that coming when I saw improvement list! haha

Awesome build! Would love to see this in person one day

Black wrinkle looks to be on point!

FYI E30 and E36 are the same. If on budget, pick a part should have a few E36 in their yards

I personally think there are plenty to go around but when they see a plead to smash the going price, people close up the stables and rather keep for a rainy day etc

Can vouch for the workmanship. Very well made splitter, strong and is aesthetically pleasing

Sent from my GT-I8190 using Tapatalk

I actually sold my LTW wing not long ago for $250 which was cheap as chips. But not risers.

Gotta love the Reiger Lip. How much did it set you back Hans?

Hit up Ray @HellBM

0212HELLBM

m52b28 crank also have m20b20 motor with the rods. Just need pistons. Know of some for sale. PM me if your interested

I'm running a UCC clutch with a single mass flywheel and the whole clutch setup weight in at about 11.5 lbs.

Going to a lighter flywheel, UCC recommended ATF with some Redline 90w-140 to reduce /eliminate chatter. I ran what was recommended and I haven't had any issues.

I have put around 2,000km on it as the car is a daily and have attended 3 skid days at Hampton and shifts really well.

It drives better than a stock clutch but she can bite like a 4puk. Highly recommend if budget allows.

I recall another member running a UCC clutch also in his E36 M3 in his hack car. And he wasn't soft on it either.

I'll take the coil harness

328i Manual output shafts from the diff to the hub available?

Few questions for you Alex.

What condition is the clutch in?

and do you have a M20 starter to go with?

Cheers

Marcus

As per title, I'm after M20 flywheel and starter.

I can do with or without the clutch also.

Pm me

Regards

Marcus

I'll take dash mat. pm'd

pm'd

sedan or coupe?

There is a 3.23 medium case on trademe currently, apparently E34/32 fitment. Not the cheapest though, given it has to be freighted up from Fielding. The E30 experts here will be able to tell you if the case will fit with the correct rear cover or not. Failing that, take it to a diff builder and have them swap the gearsets into a 188mm E30 housing, will probably owe you a bit by the time its in the car.

I'm trying to avoid the down time. Hopefully someone on here has one. Otherwise may have to send it to the diff builders and might might as well get an LSD put in at the same time

I would say 2.78 is too long for me.

Ideally 3.2x or even 3.15 or 3.3x.

2.78 is odd. What did that come out of?

Trying my luck here.

Looking for a 3.25 case diff. But anything longer than a 3.46 will be considered.

Must be medium case!

Preferably located in Auckland.

Cheers

Marcus

Is this still available?

97 E36 318ti, M-Sport. Body is good apart from a ding on the D/Door. Located in Auckland

I have for sale a Z3 steering rack.

Was off a running car in good working condition.

Comes with tie rod ends.

Pending

Also have an X-brace for sale.

Fits all E36s but will require nutserts if your cross-member doesn't already have existing thread.

Pending

Located in Central/East Auckland

PM me if you're interested.

Could you be a bit more specific when you say bobbins?

Cheers

Sent from my iPad using Tapatalk

As per title, have a set of factory springs off a sedan.

Front springs still on shocks.

$20

PM me. In Auckland.