Paragon
-
Content Count
189 -
Joined
-
Last visited
-
Days Won
1
Posts posted by Paragon
-
-
-
Got one out of a 325i in south auckland. Also have swing arms still complete to go back on it.
-
never thought of new ! So much is going NLA.
Price adjust downwards
-
-
I have one, but it has no valves, rockers and only one shaft, which doesn't leave a whole lot. I was a victim of a lack of cam belt. If that is of interest make me an offer, I can put on a courier if necessary.
-
Have you looked at the bump steer ?
-
Can do the halfshafts, out of a 320i and 2 bigger units out of a 325i. South auckland
-
Set of 5 point TRS full harness belts for sale
Only ever used for 2 days during a road car demo around a circuit.
I have co driven in a number of cars and these TRS belts are the most comfortable belts I have ever used, easily. The lock and metal work that goes into it fit around your pelvis with out sharp edges trying to take chunks out of you.FIA approved.Dates - 2010 except crutch which is 2011Delivery by courier or collect south Auckland -
I do have an enough parts to put together a stroker. Even got a choice of cranks and blocks 2.7 ground / 2.7 good nick / 2.5. Blocks 2.5 or 2.7.
-
What size should it be ? I have a wheel I thought that was off an E28 - 4 stud 15inch with 195/65 tire on it. Is that what you are after ?
-
I have a 260 box - bit bigger than a 240 - as you up for a modified trans mount and propshaft selection any way
-
yes to every thing asked for here but in Auckland. The arms could be put in a box and shipped,
-
Looks expensive for an E30, and the E36s sit at a different angle.
A G260 that was used on E30s would be a better bet. I have one for sale that is for a facelift E30 which had the crank sensor on the front pulley. The pre facelifts had the sensor mounted in the bellhousing and some kind of trigger on the flywheel. There s a bit more to the conversion than just a gearbox. Stick with E30 parts to simplify it.
-
get a facelift front pulley and move the crank sensor to the front ? Gives you a lot more options, there are very few manual pre facelift 325i's out there.
-
-
I also have one out of a 320 auto I believe, 4.4 ratio
south Auckland
-
There is lots of stuff here, time for a clean out. Mostly M20B25 unless stated otherwise. Starting with the bigger stuff:M20 2.5 block. Stripped and cleaned, ready for painting and reassembly $100M20 2.7 Block, stripped, cleaned, painted $300Crank, 2.5 standard mains and big ends 60 /40mm In good order, I would say that it does not need a grind. $100Crank 2.7 Back from the engine man. Never even been dummy assembled, looking for a new home. Grind alone cost $350. Looking for $500Bottom end, 2.5 from sump to head gasket. Worn, was using oil before it got removed. There is no lip in the bore, more a kind of ripple at the top on the thrust side only. Can’t comment on the bearings, oil pump etc because it is still all together. suit some one who wants a core to rebuild, was going okay before it got pulled out. No flywheel. $120Bottom end, 2.5 from sump to head gasket. Used. Busted a cam belt so it stopped ! Valves have touched the pistons. Bores in good condition, still see the hones hatching. Put another head on it, off you go. No flywheel, was auto. $200ECUs : Got a few -0 261 200 173 M20 2.5 $500 261 200 174 M40 1.6 $302.0 engine complete on prefacelift ECU and wiring. Came out of a running car before engine conversion, I am told 170,000 km. Inlet manifold, wiring, ecu all there. Only missing an alternator $300All in south Auckland. -
Got a G260 with cross member - dont' know if your driveshaft cope with that.
-
presumably there not free - got a a price ?
-
Wanted some doors in diamond schwartz to fit an E30 4 door. Auckland area.
Project has changed - no longer required - thanks
-
-
A pair of new rear hatch gas struts for an E36 318ti compact.
BMW part number 51242491349 these are not genuine BMW, made some where else ! $70 Location south auckland, can ship if required.
-
Beefy ones are 325i / M3 - I think the hub bearings are different - will they fit ?
I either case I have 1 320i and a 325i shaft in south Auckland
-
For sale genuine Gojack car moving dollies.
The faster castor system.
These are genuine Gojacks, NOT chinese knock offs you will see at the local panelbeaters. Last used by a British Touring car team they have had a small mod to cope with big wheels better. Model 5000, up to 565kg each. Surface rust and dust, they could do with tidy up before they go back into a race truck.
Location south Auckland $170 each, sell in pairs only. Shipping is possible.
WTB Standard Set of E36 wheels & tyres
in Want to buy
Posted · Report reply
I have a set of alloy E36 wheels, but no tires $150. Location south Auckland.