Jump to content
Sign in to follow this  
crazyarab

Need your help

Recommended Posts

Atta

5 stud win here http://www.trademe.co.nz/Browse/Listing.aspx?id=283005780

17x9" and in Chch ;)

haha, Simon you are sooo last week man :P

Went and saw the guy, he won't take less than 1500 which is a bit dear imo.. plus not a fan of the lips they don't look right.. or is it just me?

Edited by crazyarab

Share this post


Link to post
Share on other sites
Guest Simon*

I knew they were relisted but didn't know you had checked them ;)

Lips? These are 3 piece right? Lip = dish! And give the illusion of bigger diameter rims.

$1500 for Gen big ones with Conti sports isn't terrible either

Share this post


Link to post
Share on other sites

I knew they were relisted but didn't know you had checked them ;)

Lips? These are 3 piece right? Lip = dish! And give the illusion of bigger diameter rims.

$1500 for Gen big ones with Conti sports isn't terrible either

Absolutely but compare them to say..

Posted Image

They don't stagger in the way I like.

Edited by crazyarab

Share this post


Link to post
Share on other sites

Haha if you didn't want wheel issues then why'd you buy an E30??? ;)

because it goes from 10-100k in 4.5 seconds :ph34r:

Edited by crazyarab

Share this post


Link to post
Share on other sites
Guest Simon*

Not on 14x6 inch weaves it wont!

:P

E: forgot smiley ;)

Edited by Simon*

Share this post


Link to post
Share on other sites

Haha you just added half a second!!! :lol:

typo soz, timed it when I did not have LSD + drive shaft issues. That's all sorted so should have some very interesting acceleration now (can't wait to get it back from the mechanic) B) .

Edited by crazyarab

Share this post


Link to post
Share on other sites
Guest Simon*

Ha! Barrels are one thing, and as you well know Senor Gold, lips are interchangeable.

Getting hold of multi-piece genuine 17" Schnitzers to begin with is quite another ;)

Share this post


Link to post
Share on other sites

Ha! Barrels are one thing, and as you well know Senor Gold, lips are interchangeable.

Getting hold of multi-piece genuine 17" Schnitzers to begin with is quite another ;)

spot on simon but 1500 + 4 lips PLUS 5 stud = might aswell just buy a house :P !

Edited by crazyarab

Share this post


Link to post
Share on other sites
Guest Ari Gold

Proper wheels and 5 lug (not a hack job) should set you back around 5K I'd say. Some have done it cheaper, but not many.

Share this post


Link to post
Share on other sites

Can you wait 4-6 weeks for 17's? :ph34r:

i can !!

Share this post


Link to post
Share on other sites

Time to revive this thread...

Have finally got the Hartge rims down to Chch and found some spare time to mock up what they would look like. Kiril was nice enough to let me test fit them on his 5lug conversion. As you can see... HUGE is probably an understatement.

The real kicker is that the front is going to also need 20-25m spacers to fit over the wilwoods... so for this bitch to work I'm going to have to follow in westy's footsteps which is highly unlikely (as expected) :(

Also, I think these were previously fitted onto a tractor not a BMW... what the f**k kind of rubber is that! Makes it look even bigger than they already are.

post-1976-1294515927.jpg

post-1976-1294515943.jpg

post-1976-1294515956.jpg

post-1976-1294515971.jpg

Got Poke? lol...

With the right rubber it doesn't look quite so bad...

post-1976-1294515982.jpg

post-1976-1294515994.jpg

post-1976-1294516006.jpg

Edited by crazyarab

Share this post


Link to post
Share on other sites

Just buy my 4x100 Set :P

Share this post


Link to post
Share on other sites

you guys are mental..........in the nicest possible way of course :P

Hahaha, I was not going to pass up on 18" 3 piece Hartge rims regardless if they were going to fit the E30 or not :P

A man can dream right!

Share this post


Link to post
Share on other sites

Hahaha, I was not going to pass up on 18" 3 piece Hartge rims regardless if they were going to fit the E30 or not :P

A man can dream right!

i cant talk....although i didnt actually do it at one time i was ready to have four sets of wheels for the 535,one of those would have involved buying another car and reselling!

Share this post


Link to post
Share on other sites

Ok, revival of thread once again...

For the pro's what would you recommend:

BBS RS003

Rear: 16x9 ET0 (3" lips) or 16x8.5 ET12 (2.5" lips)

Fronts will be: 16x7.5 + 23mm spacer = ET13 (1.5" lips)

Need to decide today if I'm going ahead or not.

Blackie what setup do you have on yours again?

Share this post


Link to post
Share on other sites

Mine:

16x8 +7 2" Lips

16x9 +7 2.5" Lips

Spacers would be needed for anything slightly larger than stock brakes on my set-up.

Your specs look good? With a spacer up front like you've mentioned I'd go for it!

Rare will be pretty close to flush on the guards, if you're low.

DO ET. B)

Share this post


Link to post
Share on other sites

Was having a chat with Jed before and seems like getting 1.5" lips on the front might be pushing it so may have to consider sticking with 1"...

Here is a photo of what his 15x6.5 ET 33 rims looked like with 23mm spacers on.

post-1976-1316144817.jpg

Using the wheel offset calculator a 16x7 ET25 rim will poke out an extra 14mm.

Calculation:

http://www.1010tires.com/wheeloffsetcalculator.asp

Current wheel spec: Width 6.5 / Offset 10 (33 - 23mm spacer)

New wheel spec: Width 7 / Offset 2 (25 - 23mm spacer)

Outer position: Extend extra 14mm

So if I'm to get another half inch put on with the 1.5" lip I would get something like 27mm (14mm + 1/2 inch) poke outside the guard.. thinking that would need serous guard work to pull off?

So... looks like the best option is to run 1" lips front 2.5" lips back for final setup of:

16x7 (1" lips) + 23mm spacers

16x8.5 (2.5" lips) rears

Got stagger?? ":P

Share this post


Link to post
Share on other sites

My calculations could be bad, but by extending the lip 12.7mm the offset will drop from +2 to around -4.3

Which is 33mm more than the wheels you pictured. lol.

Share this post


Link to post
Share on other sites

My calculations could be bad, but by extending the lip 12.7mm the offset will drop from +2 to around -4.3

Which is 33mm more than the wheels you pictured. lol.

Yeh man, not ideal at all... hopefully with the 16" clearing the brakes properly I can run smaller spacers. I know with Jed's 15's it only JUST managed to fit without scraping :(

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...