nz320i 0 Report post Posted August 9, 2005 i put a picture here to show you whats up, The black bit that runs along the door has started pulling out where the arrow is pointing, should i just take to a panel beater to fix or something it doesnt seem to move so cant push back in? The car has been re sprayed before maybe this has been taken off before i dont know. Thanks Quote Share this post Link to post Share on other sites
325GRANT 0 Report post Posted August 9, 2005 cant remember 100% but i think there should be a bolt for the front part then clips, but there really tricky little bastard clips so they could be broken. Quote Share this post Link to post Share on other sites
ED1RTY 2 Report post Posted August 9, 2005 There should be a wierd looking plastic nut on the inside of the door at each end of the trim, then the centre of the trim is held on by the clips, its coming away where the little plastic nut holds it on so have a look on the inside of the door to see if there is a small bolt poking through with no little white nut on it...... I think thats right........ Quote Share this post Link to post Share on other sites
Gus 5 Report post Posted August 9, 2005 10mm plastic nut on inside of door, unbolt, then whole trim piece should come off. get some new clips from BMW (cost is f**k all) and replace the buggered ones. V Easy. should fit perfect after Quote Share this post Link to post Share on other sites
*sic 1 Report post Posted August 9, 2005 urethane Quote Share this post Link to post Share on other sites
Guest Andrew Report post Posted August 11, 2005 urethane or seallys all clear - worked like magic to seal my wheels hah. Quote Share this post Link to post Share on other sites
topless 13 Report post Posted August 11, 2005 i put a picture here to show you whats up, The black bit that runs along the door has started pulling out where the arrow is pointing, should i just take to a panel beater to fix or something it doesnt seem to move so cant push back in? The car has been re sprayed before maybe this has been taken off before i dont know. There is a plastic clip at the front that is probably broken. To assemble the trim on the door, you slide the front bit into this clip, click the trim into the next 2 plastic clips and then put the plastic nut on at the opening end of the door. Try taking the nut off, lift the trim away from the door enough to clear the thread from the panelling and slide the trim backwards. It should clear the clip. The most common fault with these clips is one or more of the 4 tags that spread open when you push the centre pin in break off when you remove it to paint and then they dont stay fixed in. Have attached a pic of the door with the first 2 clips visible and the trim above them removed and placed upside down. This is a facelift door so should be like yours. Quote Share this post Link to post Share on other sites
bimmer boy 21 Report post Posted August 11, 2005 My door! I always wonderd how to get the rubibng strips off Quote Share this post Link to post Share on other sites
topless 13 Report post Posted August 11, 2005 Yup, your door..... BTW, that car of yours must have had a swim sometime, all the widow motors were siezed and the central locking motors had been replaced with cheap aftermarket ones... Quote Share this post Link to post Share on other sites
nz320i 0 Report post Posted August 11, 2005 Yup, your door..... BTW, that car of yours must have had a swim sometime, all the widow motors were siezed and the central locking motors had been replaced with cheap aftermarket ones... wtf?na man cos i put in central locking with remote so replaced motors and the bmw ones were in the doors?? Do you know this car ?? Quote Share this post Link to post Share on other sites
nz320i 0 Report post Posted August 11, 2005 Oh well cheers everyone will fix it up this weekend. Quote Share this post Link to post Share on other sites
Surge 1 Report post Posted August 11, 2005 Nah, he was refering to bimmer boy, who he got brought his car as parts from nz320i - he hasn't actually worked on yours Dad knocked his bump strip off below the indicator, looks rather clean without... may have to take them all off and weld in a panel then get it all re-sprayed. Quote Share this post Link to post Share on other sites
topless 13 Report post Posted August 11, 2005 wtf? na man cos i put in central locking with remote so replaced motors and the bmw ones were in the doors?? Do you know this car ?? Hey sorry, was just replying to Bimmer Boy .. My door! I always wonderd how to get the rubibng strips off As Surge says, I bought his car off him and stripped it for parts. Quote Share this post Link to post Share on other sites
