Linden

I'm pretty sure I spotted one on that 320i parked in your driveway.

dont mind push starting, dont have a m20 boot though just a m40 one, gunna need half a tube of silicone to make that fit lol

Hey guys finished my conversion i just need a proper intake boot and a starter motor so if you've got one in dunedin let me know asap! Cheers Linden 027 3111 976

PM'd

Hey so ive got pretty much everything swapped in, I tried to use the M40 starter but im guessing its quite different as it doesnt engage??? or is that just my c101 pins not lining up so it isnt being told to engage??

Is there anywhere in dunedin i can buy one???

I got a clutch slave cylinder from BNT and it did not come with a rod (I was told it would have it when i ordered.....) and i need one tomorrow as start work in chch on monday!!!

Hey guys just purchased a Clutch Slave Cylinder and dont have an actuating rod so going to try make one, Can someone let me know the exact length of the actuating rod thingy that goes into it?? Cheers Linden 027 3111 976

What am i expecting to pay for one? im on a bit of a budget and have to get back to chch to start my new job on monday lol

Hey guys just doing my m20+manual conversion and im missing the Clutch Slave Cylinder off the tranny. if anyone has one in dunedin it'd be fkn awsome!!! 027 3111 976 Cheers Linden

just about to leave chch now, giz a text'a'roo 027 3111 976 Linden

My numbers in the top post, Im down today till sunday unsure how long it'll take for me to swap the motor so dunno if mine will be on the road lol

Cheers man, Im doing the conversion at my brothers by woodhaugh so ive already got a place to send it to, would be good to see some beemas while im down there though

Cant wait for the next one, was awsome to meet everyone aye.. Mark can i get a copy of the first photo in the flickr stream please?

Loving the first pic man, looked fkn good when i saw it the other day aye, tint them taillights ? ps. is it me or does your passenger door look a different colour or is it just the pic i never noticed it before

Switched as in ACC on? or am i just going to make a fool out of myself, If thats what you're after I wired up to the back of the rear demister plug/button in the dash, it was pretty easy as it pops right out

sweet cheers bro, gimme a text as I may be driving down to dunners at the time

If i have no luck will do, Im currently in CHCH but driving down to Dunners to do my engine conversion and missing those parts

Hey guys I urgently need a M20 Distributor cap and the rotor arm that sits inside, also need leads #1 and #5 ( will buy whole set if i have to...) Pref pickup from Christchurch or Dunedin If you could get back to me asap give me a text on 027 3111 976 Cheers Linden

Sweet cheers bro i might give you a text tomorrow, cause im prolly going to need tograb a few bits before i head down to dunners on Wednesday do the m40 starter motor and alternator fit the m20?

Hey guys Im about to convert my car to a m20 so this engine will be available, it only has 133kms on it too The engine and autobox run beautifully revs smoothly no smoke at all etc, engine seems like it has been well looked after, it just had a service on engine and auto before i bought it too (engine will only rev to just below 4100rpm - unsure why, it feels like it just hits a limiter) so ya know i havnt been redlining it i guess lol Carjam link on engine KMs of engine - linky If anyone is slightly interested it can be driven before wednesday just text me. If no interest i may leave it in Dunedin as that is where i am doing the engine swap (will bring it back to chch otherwise) Not sure what anyone is willing to pay for it but i guess around $400? but need it gone Cheers Linden 027 3111 976

It was a cool first meet for me too and I had lots of fun without even burning any tyres hehe

yeh im pulling everything out of a written off car I just want to know what i can get away without swapping (i ment the guage cluster not the whole dash btw lol) "connection from engine to carside loom is a circle the whole swap will be plug and play" so the part of the loom that plugs into the ecu is the same? - I guess im just gunna have to go down and try it all out arent i lol

Hey guys didnt want to highjack Andrews thread with questions as mine relates to a 318... Im going to convert my '89 FL m40 auto to a 2.5 Manual from a pre fl, (has dizzy on the front of engine, ive been told some have it on the side..) I have to drive to dunners in my time off to convert it so want to make sure i have all the extras I need, Am I able to keep my current FL dash (as it only has 133kms on the car) and use my existing loom (and maybe change the coding plug?) _or_ do i have to use the pre fl/dash from the donor car _or_ maybe use a later ecu like said in Andrews thread Should i just get a toothed crank pulley and 325i FL ecu or is my m40 loom still not interchangable with m20's ?? Cheers Linden

BS - Welcome to Bimmersport, Now get ya tits out luv