Arron

Picked up my new flywheel yesterday We will be using a sprung disk It is only a 228mm flywheel as we have a dprubg disk here for it already, we are also having a pressure plate re built and up rated For us having the 240mm flywheel didnt really achive much, we are only running on clay so there isnt as much grip as a seal track, The guy who made it was from dynamic engineering

Picked up my new flywheel yesterday We will be using a sprung disk It is only a 228mm flywheel as we have a dprubg disk here for it already, we are also having a pressure plate re built and up rated For us having the 240mm flywheel didnt really achive much, we are only running on clay so there isnt as much grip as a seal track, The guy who made it was from dynamic engineering

we have just gone through this with one of our s50b32 engines, our dual mass was naffed. e we looked into a lightened kit from nzad but after some reading and speaking to one of ouf engine guys we have decided not to because the lightened flywheels can upset the harmonics of the engines and can cause flywheel bolts and crankss to break along with other stuff we have had a flywheel made up but have had it machined to the factory weight so we dont cause any issues to have a flywheel made was not expensive at a little over $400 the person who is making our flywheel has made a lightened onoe for a 328 before and 3 days later he gets a call saying he has snapped the crank in 2. (this is assuming of course the kit you hhave been quoted is a light weight flywheel)

Cheers for the thoughts guys It was dynoed in 5th gear which for us is 1:1 It was scanned on a snap on scanner but he is coming back over shortly with the BMW program and we will be doing the Vanos test

hey there. i think they are only 7.5 inch but will check this afternnoon

howdy all had my race car on the dyno last weekend and thinks are not looking the way they are ment to...... we are lacking quite a bit of power from where we should be hatched is the dyno chart we peaks at 160kw at the wheels as can be seen on the chart there is alot of hesitation then a huge jump around the 3k mark, from what we have been reading is it possible for that to be a sign that the vanos needs to be rebuilt? 9had the engine scanned afterwards and the exhaust cam is out by upwards of 4 degrees) also from the a/f ratio we can see that it is running rather rich, we have since had the car scanned and nothing has shown up. we have since found a air leak so have sorted that but if anything we thought that would make it run lean (unless it has put the o2 sensors outside their reading range so it has gone into a "safe mode" do any of you have any things to check or look at to work out why it is running so rich?? the a/f ratio is between 11.6:1 and 12.1:1 so it is reasonably rich possible dud o2 sensors, or any other reasons you could think of we are currently looking at buying our own a/f ratio meter so we are able to keep looking at if things we change/try change the a/f ratio any thoughts,advice or info that you guys have would be appreciated Attached Images

howdy all had my race car on the dyno last weekend and thinks are not looking the way they are ment to...... we are lacking quite a bit of power from where we should be hatched is the dyno chart we peaks at 160kw at the wheels as can be seen on the chart there is alot of hesitation then a huge jump around the 3k mark, from what we have been reading is it possible for that to be a sign that the vanos needs to be rebuilt? 9had the engine scanned afterwards and the exhaust cam is out by upwards of 4 degrees) also from the a/f ratio we can see that it is running rather rich, we have since had the car scanned and nothing has shown up. we have since found a air leak so have sorted that but if anything we thought that would make it run lean (unless it has put the o2 sensors outside their reading range so it has gone into a "safe mode" do any of you have any things to check or look at to work out why it is running so rich?? the a/f ratio is between 11.6:1 and 12.1:1 so it is reasonably rich possible dud o2 sensors, or any other reasons you could think of we are currently looking at buying our own a/f ratio meter so we are able to keep looking at if things we change/try change the a/f ratio any thoughts,advice or info that you guys have would be appreciated

yes it will be up

we have heard that before about the cast wheels not liking high rpm we have also thought about making one, we have all our own lathes and mills at home but its just the time factor this morning we have been in contact with nzad and can get a chromoly 240mm flywheel for $550 so after having a converstion with them we might just looking at buying a flywheel and clutch kit from them out of interest hoe much did it cost to have the flywheel mad up? cheers

sorted

updated the gearbox is a getrag 220, it is out of a 4 cylinder but can change the bits over to fit 6 cylinder as we have them here to do so

hi guys we have been having a few clutch issues on our s50s lately and we have just pulled mine out, the dual mass flywheel has seen better days so we are looking at what other options we have does anybdy know what the deal is with the m20 flywheels? we have been offered a m20 flywheel and would like to know what starter motor and thrust bearing ect we have to use does the m20 have a different clutch and pressure plate to the e36's? any help/advice is apreciated

hi guys we are after a flywheel and clutch kit to run on one of our s50 engines doesn't have to be factory but preferably near new or if no brand new we are looking to order one in the next couple of days so pm me if you have anything thanks in advance

HUGE CLEAR OUT!!!!!!!!!!!!!!!!!!!!!!! E36 Manual conversion, just had a rebuilt gearbox and new clutch $800 Comes with everything needed minus diff E46 mags and tires $350 ono good condition, 2 near new tires 2 bald E36 m3 mags and tires, 2 near new tires 2 bald good condition $500 E36 mspec rear bumper, damaged but repairable $100 ono E46 mspec front a d rear bumpers, rear in good condition, front is damaged but repairable, we have started the repair just needs to be welded up $300 ono S50b32 oil cooler and oil cooler housings, good condition Oil cooler and housing $300 ono Oil cooler housing $150 ono E36 ti rear end, perfect for a e30 5 stud conversion $200 ono E46 mspec 4 door sill covers near perfect condition $100 E36 ti arm wrest and centre console, near perfect condition $120 ono E36 mspec side skirts, good condition $120 ono Racing dynamics body kit off of a e36 $200 ono good condition Factory e36 tow bar, $150 ono, comes with all the mounting bolts, Boge rear shocks out of a e36 328 good condition $100 ono Numerous sets of coupe and sedan tail lights, will up load pics of them tomorrow more to come!!!!!! all located in christchurch will ship at buyers expense

sold pending payment

up make an offer

Ac schnitzer type 2 mags 17x8.5 inch 2 half worn 215 45 17 tires Good condition, Each rim has some curbing Will upload close up pics this afternoon $500 ono Located in Christchurch

Yes it is small case

Complete rear end out if a e36 to Perfect for a e30 5 stud conversion Comes with a 4.44 ratio diff $200 ono Located in Christchurch

Trying to track down some information on the p50b32 engines Have asked Mr Google but I have not managed to find much Really just want to know what the difference is between the s50 and p50 Cheer

ooops

If I bring 2 BBQ and steak for everyone....... Can I run a m3

uppppp, sorry 1 is missing

hi guys what do you think about running e85 in a s50b32?? the engines are in our race cars so dont get driven lightly is it a good idea to run e85? or would we have to have the dme remapped and put bigger injectors and or fuel pumps in them?? any thoughts are appreciated

yip off season plans so far are we are pulling dads engine out to give it a bit of a birthday, arp rod bolts, new rear crank seal, rebuild the vanos unit, possibly a head gasket after this weekend and a full new set of panels and some modifications to the car itself for my car we will be pulling my graebox out and replacing the clutch as i cooked it in the last race this weekend,pulling the engine out and putting arp rod bolts in mine to, a full new set of panels and get both of them on a set of corner weight scales oh and we will be putting some graphics on both cars for next season........ with a 3nz on mine somewhere