Deano

Hi...where in Welly are you>

$2800 ono...Will be going $1 reserve on TM soon.

I need to sell this soon. Probably go $1 reserve after classified listing ends on trade me. Offering to bimmersport $2800 ono..

Wedding on 6th April in Wellington so could bring it up..

I had a similar problem. Worked ok from cold but once warm run rich and real gutless. Turned out to be temp sender for the ecu

Could deliver to north island, have a wedding in Wellington over easter, open to offers, need to sell tidy and original E30 C'mon!

Its an odd one...could be an early racing dynamics? But no sport steering wheel but has the Dog leg E21 sport box which are rare and worth mega and try find an E21 3.45:1 LSD..I might put an offer in!

Hi,

I'm after a temperature sensor, one for the dash, part number is 12621747281

Anyone have some 'good' used ones around? Rather try some first than spending a pile on a new one just yet.

Cheers

I have one here from E36 320i but number on the side is 1710535 VDO and 130 deg max. Black two pin plug.

I marked it temp gauge when removed so pretty sure its the correct one $20 to you

Will put up soon, was considering getting dents repaired

New warrant on..will be on trade me soon

Complete K-jet injection system

2 unmolested fuel distributors and WURs

Good set of fuel injector feed lines

2 sets of injectors

Packet of new injector seals

Cold start valve

Air by pass valve

Offers for the whole lot or individual items

Tidy original SA assembled E30 325i auto

1989 214 000ks

Excellent motor and transmission

Well looked after, drives well

Has new WOF $2600

Any interest either PM or text on 021 230 4284

I had one, missed the post haha, Gavin is good tho.

Will take it as well - PM sent

Does anyone know which model E36 these diffs are out of? Im guessing the 318is but not sure. Also what ratios are available and how difficult are they to get hold of and is the 168mm diff the small case diff?

Sorted Gavin comes through again $48.75 +

damn good price

Hi..anyone have a surplus head gasket unused lying around?

Text me on 021 230 4284 before I go retail!

Cheers

Transmission in my e30 is stuffed. Is currently auto. Would like a cheap auto replacement so I can fix and sell the car.

Any help would be greatly appreciated

Sam

0212997586

What area are you in?

As per following picture,

after a set of these, hopefully someone has a set off some bottlecaps or similar.

Let me know if you have anything kicking around,

Cheers.

Yes I have a good set with all unfaded BMW badges..one has small dent but will chuck in undented spare with bad badges..021 230 4284

these rims, in the photo, anyone got them??

can paid cash, or swap you mint 14 inch e30s rim.

akl based, but will be at chch, welling soon. so anywhere really.

Andy

0212698650

I have one as a spare in my E21 but have a steelie I could use if your desperate

Anyone got an extra one turned up that they want to sell or recommend anyone that can make one up for me?

Cheers

Pm or text 021 2304284

Anyone able to turn up the front oil seal spacer from the old E36 pulley hub for me at reasonable cost?

Cheers

I built a 2.7 last year with E36 320 injectors...they are slightly higher flow than E30 325 with better spray pattern with the 4 pintles and worked well. Also tried some 19lb yellow mustang injectors off ebay and they worked good too..but to get power out of strokers you got to upgrade the cam, dial in, then remap

Building a 2.8 soon based around a near new 288 schrick I managed to procure..

Further investigation reveal facts from SA import handbook from 1989 model I have as 9.4:1 engine coded 25 6E 2.

Can anyone else add there wisdom?

Been researching this and come to the conclusion without comparing pistons and stripping the engines etc is

Blocks marked 25 6E 1 or 2 are 9.7:1 CR and found in pre facelift, pre cat Euro's and SA imports

Blocks marked 25 6K 1 or 2 are 8.8:1 CR and are the Catalytic preped engines as found in Jap imports and US spec motors.

??

Hi guys wondering if anyone has one of these # 21511204525 e21 throwout bearing 30mm tall. Will be using it for my m20 flywheel conversion. Or any place which will sell them. apart from bnt $136 ouch.

Cheers

Probably have one at home. Not back for 10 days but you should fit a new one. Try Euro Italian for a better price