Search the Community
Showing results for tags 'schnitzer'.
Found 7 results
-
Build Date March 1994.Chassis JB02939 Reg No SS1338 Supplied by TMBMW July 1994.Full service history. At a cost of more than $110000 on the road there were not many of these AC Schnitzer S3 silhouette coupes bought into NZ. With the M50 2.5 engine producing 190 HP,a top speed of 150MPH and 0-60 in 6.5 seconds (AutoCar magazine Aug 1994) this car was no couch potato, these are respectable figures even today. One owner till June 2013 and on the mainland since, it has travelled 96000 kilometres. Always garaged, driven in the dry only,and in perfect original condition. $13000 For more detail PM or call 029 777 4006 Thanks for reading Update 05 October 2017 Car sold in Feb 2016 to third owner in Tauranga. And in July this year 2017 we bought the car back. It has a recent service with Coombes Johnson in Tauranga, and a complete four corner suspension refresh (Bilsteins), new bushes and sway bars, and new brake rotors too. So now it is really is a show car, and go car! The car is still in Tauranga, and if we don't sell it or deal it on something else I'll bring it back to the South Island, although at the moment there is no room in the garage! Link to more photos: http://waimakclassiccars.co.nz/cars/353_BMW_325__E36_AC_Schnitzer.html Call, PM or email me at [email protected] for more information.
-
Can anyone recommend a good source for 17" lips? Currently looking at http://www.felgenfuchs.de/en/Outer-Lips/17-Inch/ACSchnitzer-Outerlip-17.html
-
Set of 4 replica ACS Type 2s in 17x8.5 et13. No ACS or Ronal markings anywhere. Actually, no manufacturers markings! They are stamped JWL. (For details of JWL, see here. These were on Miss M's E36 when we bought it - et13 is not the best fit , although to be honest there was very little rubbing. Arches have been rolled to fold the inner lip, but as far as I can tell, that is all. Lips on all 4 rims have been kerbed, and rather than refurbish them, someone has painted the whole rim instead. (I think it is paint rather than plasticoat.) They look pretty good until you inspect them closely, at which point the grazing and suchlike is evident. No massive chunks missing - just untidy. Tyres fitted are all 215/45ZR17: 2x virtually brand new Vitora Sportlife. 7mm++ tread 1x Michelin Pilot Preceda. 3mm tread, slightly less at the edges. 1x Bridgestone Potenza RE05A. Less tread than the Michelin and showing edge wear, but still just about usable. It passed a WoF. I suspect the Michelin and Bridgestone have been run under pressure as there is more wear on both inside and outside edges. Given the size of the rim and the tyres fitted, I had expected them to feel much heavier. According to the bathroom scales, each rim and tyre combo comes in around 20.5kg. Collection in Te Kauwhata or Manukau, delivery for a small consideration in the local area. If national transport can be arranged via the forum, I'll help out with that but would much prefer to not get into courier shipping if that can be avoided. Need 'em gone, and need some money for new tyres for the E46! (Especially now Miss M has commandeered the Style 73s.) $350. From what I can find, genuine are worth $6-800. I think these would be around 50% of that.
-
Some time ago I acquired some very nice suspension parts for our 320D but for a number of reasons it now seems unlikely we'll be using them. Mainly, Mrs M's arthritis isn't getting any better and it may be pragmatic to buy a vehicle which is a little taller so she can get in and out more easily. This is a pair of AC Schnitzer sway bars (anti-roll bars, as we of English origin call them ). They are made for ACS by Eibach. Vivid Racing list the ACS bars at $1384 (less discounts and so on); the Eibach bars are listed at $700. (Both plus shipping and so on.) You may not be able to see it clearly in the pic, but both names are clearly printed on both bars. Part numbers are 313546311 (front) and 313546312 (rear). The ACS p/n for the set is 313546310. The Eibach p/n for the set is E2066-320. I'm told these will fit all E46s, except (perhaps) the M3. Front bar is 27mm; rear bar is 21mm. Don't fit just the front - fit both. Your car will understeer if you fit just the front bar. What's in the pic is what is included, so you get the links and all bushes too. All bushes look to be in good condition. Asking $350 - half new listed and discounted price..
-
I have a set of 4 genuine ACS Type 2 rims, 17x8 H2 et38, from an E36 coupe. I was going to fit them to the E46 Touring, but Mrs M isn't keen and I still have the Style 73s which do meet with approval. The inside of one spoke on each rim has AC Schnitzer cast into it; another spoke has Ronal. Tyres are 3 Maxtrek Ingens A1 with 6mm tread (please check 'em for yourself) and one Kumho Ecsta, all in 215/45-ZR17. The Kumho has camber wear on the inner edge but would pass a WoF without issue; again, it has ~6mm tread. Rims are all original and have not been refurbished. They have the original AC Schnitzer film logo on the outside of one spoke - I contacted ACS about this and unfortunately the films are NLA. The rims would have been painted, the logo applied, and clearcoat over the top. You can't feel a lip or bump where the logo is. All 4 rims have some kerbing and would benefit from being dressed. Perhaps this could be done without a full refurb, so the logos could be retained? Full set of 4 AC Schnitzer centre caps, too. I'll post some pics in a bit. I could bring to Kyu's tomorrow if anyone is interested? Price... Hmm. I've seen the Maxtrek Tyres offered at $155 each, so s/h the 4 would be... $250? Rims... Jason had some without kerbing or tyres and was looking at around $600. (Don't know what happened there.) How about $550 for the set of 4, with tyres and centres? Make me an offer.
-
All part of the garage clean out.........must have more space 1)Set of five schnitzer monobloc rims 16x8 inches ET35.2 slightly scuffed three are perfect.With centre caps. Suit e30 M3 E36 M3 and others.5x120 stud pattern CB 72.5 $600 the set plus freight.Can deliver to Mainfreight, place on pallet and on send to you.Seems to be the best freight option around NZ.Bought for a project but changed direction........On Trade Me too need the space in garage for other stuff! 2)Schnitzer Rennsport made by Ronal (type 2) with the peg holes.Three piece rim.Set of four 17x8 and 9 inches et 35 front and 45.5 rear.Slight scuffing but an easy fix to polish out.Centres are perfect. Suit E36 M3 E46 and others 5x120 stud pattern CB72.5 Very rare rims The discolouration in the photo is coppaslip.Bought for a project but changed direction again... $1200 the set THANK YOU SOLD 3) Set of five (3 F 2 R) BMW style 39 DS11.17x 7.5 and 8.5 inches.As fitted to the E36 M3 Evo coupe.Almost perfect but not quite.Fitted with Continental Contisport (6mm+)to the front and Goodyear premium(7mm) not quite sure of the style on the rear Spare is a new Michelin. Tyres are not that new but with even tread wear and no high or low spots.I refurbed another set of rims and fitted Michelin PS3 all round so these are surplus.And taking up space. $850 the set including the tyres. THANK YOU SOLD Pm or call 0297774006 And thank you for reading
-
Hello, selling this car on behalf of my dad. it's a 1981 635 CSI Schnitzer S6. 89567 ks - Automatic Original Schnitzer 635 Csi S6 1981. Imported by BMW NZ as the manager's car. My dad has had this car since 2006 and has carried out all necessary repairs on lights, brakes, shock absorbers, starter motor, steering joints, tyres, all receipts kept. He has only taken car out in summer - garaged year round. Located in Wellsford - Auckland. We're looking for around $28k. Enjoy. Please contact me, Leighton on [email protected] or 021407307 or contact my brother Alex - 021682526
