Paragon

I have a set of alloy E36 wheels, but no tires $150. Location south Auckland.

Radiator out of an E36 M3 Evo, 3.2 been stored for the last 5 years. $230. Can organise a courier or collect south Auckland

Got one out of a 325i in south auckland. Also have swing arms still complete to go back on it.

never thought of new ! So much is going NLA. Price adjust downwards

Set of locking wheel bolts with key in really good condition. Came of an E28 but probably fit most BMWs of that era. Pictures explain it better - Can post / courier $120

I have one, but it has no valves, rockers and only one shaft, which doesn't leave a whole lot. I was a victim of a lack of cam belt. If that is of interest make me an offer, I can put on a courier if necessary.

Have you looked at the bump steer ?

Can do the halfshafts, out of a 320i and 2 bigger units out of a 325i. South auckland

Set of 5 point TRS full harness belts for sale Only ever used for 2 days during a road car demo around a circuit. I have co driven in a number of cars and these TRS belts are the most comfortable belts I have ever used, easily. The lock and metal work that goes into it fit around your pelvis with out sharp edges trying to take chunks out of you. FIA approved. Dates - 2010 except crutch which is 2011 Delivery by courier or collect south Auckland

I do have an enough parts to put together a stroker. Even got a choice of cranks and blocks 2.7 ground / 2.7 good nick / 2.5. Blocks 2.5 or 2.7.

What size should it be ? I have a wheel I thought that was off an E28 - 4 stud 15inch with 195/65 tire on it. Is that what you are after ?

I have a 260 box - bit bigger than a 240 - as you up for a modified trans mount and propshaft selection any way

yes to every thing asked for here but in Auckland. The arms could be put in a box and shipped,

Looks expensive for an E30, and the E36s sit at a different angle. A G260 that was used on E30s would be a better bet. I have one for sale that is for a facelift E30 which had the crank sensor on the front pulley. The pre facelifts had the sensor mounted in the bellhousing and some kind of trigger on the flywheel. There s a bit more to the conversion than just a gearbox. Stick with E30 parts to simplify it.

get a facelift front pulley and move the crank sensor to the front ? Gives you a lot more options, there are very few manual pre facelift 325i's out there.

is the heater a standard or air con model ? Fog lights - are these the same as the 320 / 325 pre facelift ? the mounts look different.

I also have one out of a 320 auto I believe, 4.4 ratio south Auckland

There is lots of stuff here, time for a clean out. Mostly M20B25 unless stated otherwise. Starting with the bigger stuff: M20 2.5 block. Stripped and cleaned, ready for painting and reassembly $100 M20 2.7 Block, stripped, cleaned, painted $300 Crank, 2.5 standard mains and big ends 60 /40mm In good order, I would say that it does not need a grind. $100 Crank 2.7 Back from the engine man. Never even been dummy assembled, looking for a new home. Grind alone cost $350. Looking for $500 Bottom end, 2.5 from sump to head gasket. Worn, was using oil before it got removed. There is no lip in the bore, more a kind of ripple at the top on the thrust side only. Can’t comment on the bearings, oil pump etc because it is still all together. suit some one who wants a core to rebuild, was going okay before it got pulled out. No flywheel. $120 Bottom end, 2.5 from sump to head gasket. Used. Busted a cam belt so it stopped ! Valves have touched the pistons. Bores in good condition, still see the hones hatching. Put another head on it, off you go. No flywheel, was auto. $200 ECUs : Got a few - 0 261 200 173 M20 2.5 $50 0 261 200 174 M40 1.6 $30 2.0 engine complete on prefacelift ECU and wiring. Came out of a running car before engine conversion, I am told 170,000 km. Inlet manifold, wiring, ecu all there. Only missing an alternator $300 All in south Auckland.

Got a G260 with cross member - dont' know if your driveshaft cope with that.

presumably there not free - got a a price ?

Wanted some doors in diamond schwartz to fit an E30 4 door. Auckland area. Project has changed - no longer required - thanks

location ? for gandering

A pair of new rear hatch gas struts for an E36 318ti compact. BMW part number 51242491349 these are not genuine BMW, made some where else ! $70 Location south auckland, can ship if required.

Beefy ones are 325i / M3 - I think the hub bearings are different - will they fit ? I either case I have 1 320i and a 325i shaft in south Auckland

For sale genuine Gojack car moving dollies. The faster castor system. These are genuine Gojacks, NOT chinese knock offs you will see at the local panelbeaters. Last used by a British Touring car team they have had a small mod to cope with big wheels better. Model 5000, up to 565kg each. Surface rust and dust, they could do with tidy up before they go back into a race truck. Location south Auckland $170 each, sell in pairs only. Shipping is possible.