slybma

ill take a set PM'd you

It was a full respray it used to look like this

Put me down for a set in the next order too

took advantage of the nice weather this weekend and rolled the car out of the garage and gave it a bit of a clean the 5 stud conversion starts this weekend more pics will follow

Finished installing e36 leather seats in my e30, starting to look like a car again now.

Im looking for a few interior parts to finish off my E30 coupe i need; -Hood lining -Both 'B' Pillar covers -Passengers front seatbelt and lower slide mount -Both drivers and passenger side footwell/lower door sill trim -An E36 sedan black leather seat top and bottom -Also need a Facelift fog light for the drivers side Also after an M20 drive shaft and selector rods to finish my M50 conversion hope someone can help

This all goes to scrap tomorrow if anyone wants anything, last chance

Could be convinced to sell my e30 with an m50 swap, needs finishing off. Pictured below

The hose kit in your trade me link will be fine for a WOF because they are a direct replacement kit not a piece together type kit with the screw on fittings, i have the exact same kit on my e30 and have never had any wof issues.

Having a clear out of the garage and found all my old M40 engine parts that i no longer need so i thought i'd see if anyone wanted any of it before it goes to scrap metal. B16 engine just had a recond head and new lifters before engine being removed due to running a big end so really only good for the head $80 Sump pan no damage $50 Franklin Cams Mild race cam 270 Duration 10.9mm lift brand new only in the engine a week before removed SOLD B18 Short block good cond. $50 Have all the engine accessories also, if you need anything else just ask and ill see if i still have it all going cheap.

Thank you for that pin out chart, I checked the adaptor I had against it and found two wires had been mixed up, all sorted now

I have a sump $100 if you want it

Most of the wiring hasn't been removed since it was running in the e36, I'm running a harness adaptor but I'm not positive the wiring is right for my conversion, does anyone have a proven pin out that works? It's going into a 316i factory manual nz new, cause looking at it this weekend I noticed the IAC valve hums with the key on...The vin isn't readable on the ecu I managed the last 7 to be jb02528 The ecu number is 0 261 200 413 red label Any help is really appreciated

hi guys im doing an M50 swap into my E30 and seem to have hit a snag with the ecu, i have a red label 413 DME wiring is all done and the engine cranks but no fuel or spark??? is there anyway of telling if my ECU has EWS I or II by looking at it? if so can i get a chip to bypass it or am i better trying to find another ECU the car it came out of is that i know its from a 10/1993 e36 manual 325i any help would be greatly appreciated

how much for the hood lining, b pillar trims and the black trims at the bottom of the inside of the doors, that sit over the door rubber.

I appreciate the help, I suppose ill find out when I put the engine in

I'd say that some of the reason behind the temp drop is due to the temp of the trans fluid being lower now that its new. If the trans fluid is colder now than before that means the temp in your trans colder so its not heating the engine radiator up as much which may give you the slight drop.

the main thing im worried about is the gearbox if that fits im happy to alter the rest

Awesome thanks for the info, in that case i dont need to buy anything i just assumed that the m40 bellhousing was different to the m50. Its going into a 1989 f/l 318i factory manual.

the e30 240 gearbox fits right up?

as per title, im after a gearbox to complete my E30 M50 conversion. Aslo looking for a driveshaft, crossmember and selectors to suit.

where abouts are you located?

you still have the door cards and parcel tray?

Thought i'd add a link to a couple of photos of the before and after of my E30 build, will upload some pictures of the engine later. http://www.bwccustoms.co.nz/webapps/i/100856/321594/489426