Leaderboard

Reset / clear the fault code. With ignition on, tap the ABS module. If the light comes on with same fault code, it's the module

Update. Department of Beep Beep! Some horn material, yesterday. Brought to you by the department of bad puns. A friend kindly dug these out of his parts stash. A pair of 325i Fiamm horns, one high, one low, complete with brackets. Along with a couple of connector shells, sans pins. (I must be) need a couple of nuts. And either there will be good fortune when I get underneath it and all the wiring is there to plug into, or I'll find those crazy Germans put in different looms. In which case I'll need to find the right pins for the connector shells, and make up some cabling to run from the central 'meep meep' horn to these PaaaaarrrrRRRRPPP horns. One goes on the Right side, and one on the Left (or wrong) side. Depending on your viewpoint. Wish me Luck! @adro next time we catch up I'd like to have a look around your SE to see how it's been done. Other things... Twirly thing I lucked-out, and nabbed a three-spoke leather OEM Sports Steering Wheel (aka SE wheel) from the book of faces, recently. It's pretty tidy, was just a bit faded. I've cleaned it, given it a couple of coats of black leather toner, followed by two coats of leather protectant, and a couple of coats of Elephant Leather preservative. I'll get it onto the car soon. Being fastidious, I've ordered a new locknut. ? Graunch in suspension. The Graunch of Suspension Wood, has been diagnosed by Jon at Auto38. Inner tie rod. I'm going for gold, and we're going to do tie rods, wishbones, lollipop bushes, and replace the steering guibo. I'll install the 20mm front bar, with new bushes & Meyle HD end links. That'll do for the next couple of months while I refurbish the Style 5 rims, and then the 51mm strut housings. This work will get it steering straight and true, and eliminate older (as in 15-20 years, probably) bushings and balljoints. Jon spanner-checked it, and it's a bit 'tighter'. The rest of it (excepting the tie rod) is all still WoF standard, though I want the front to feel as good as the rear end now does. Strut Housings Of the strut housings, thanks to @gjm & @_ethrty-Andy_ for the Bimmersport Good Bstard Express™ assistance from @nick496's. I have all the parts for the strut builds, including new wheel bearings. Just need to sort springs. Sampling @adro's SE last week, I think I'll be able to live with HR Sport Springs to match with the Koni Yellows 8641-1210 Sport (front), & 80-2522 (rear). Abrasives and PPE I've ordered new filters for my 3M mask, and a bunch of abrasives to use with my Dremel and handpiece. It's going to be slow and steady prepping those buggers for paint. I've a large box to lash up a paint booth out of, and an old office chair that I plan to make a wheel spinner out of. Need to figure ensure all rims are true before I start (a precaution only), and cut the valve stems out. Questions about paint Now to source paint for the wheels. Thought about standard Wheel Paint (Felgen Silver) with clear. Nah, I'll get Granitsilber mixed up in aerosols, and clear coat. I liked the idea of Nogaro Silver, but it's darker and too close to Lachssilber. I'll pay a lunchtime visit to Union Hardware soon to source paint. Just thought, though... I have an airbrush compressor, and an airbrush I've little experience with... though it'd probably take an age to paint wheels with an airbrush, eh? Paint would be going off while I'm still painting. I'll keep it simple and go with aerosols, no clean-up. For the strut housings, I'm going to strip them down, rust preventative, etch prime, and two coats of Rustoleum gloss black. Questions - Paint: If you've thoughts or tips about painting my wheels, please let me know. 1k vs 2k, type of paint to withstand wheel heat, etc. Questions - Horns: If you know what bolt/nut, or in particular what the connector pins are for the horn connector shells, please let me know!

Some light entertainment for the BMW fan, apoligies if this has already been posted

It's a real nice idea but a higher km UK car running a g220 isn't particularly appealing

Im hoping its a decent price, would like to see it go to a good home. I did the steering wheel, an Ebay company that does custom cut real leather covers for about $60, you just have to do diagonal stitching, not much worse than threading new shoe laces.

The M850i. The only one in NZ. And my daughter has been for a drive in it.

You know it’s funny I have been on this site regularly for over 10 years (without being a regular contributor) and overtime you notice the absence of people who were regular contributors. He is one of them. Last I heard was that he was selling his M5 to replace it with a X5.

Interior photos added will remove the stainless vinyl for buyer or provide the remaining sheet so they can redo or finish the job. 3m 1080 brushed steel

Drool... https://www.trademe.co.nz/motors/used-cars/bmw/auction-1952526407.htm?rsqid=d22e1603f8c649feaf7df57debcc5f95