BM WORLD

brake upgrade on the e28 m535i details and pics here . http://bimmersport.co.nz/topic/31734-project-rebuild-m88-engine-bored-stroked/page-5#entry566721

quick update , swapped out the 540i e34 302mm by 28mm front brakes for some e31 850ci calipers 324mm by 30mm discs and pads from a e38 740i stops nice anybody want some e34 540i front brakes for there e28 e24 e34 etc

just book the car in , can be a pig of a job if the bearing is stuck , (welded itself in) may require new arm etc

I might know someone and his brother that might be selling one soon

haha yea maybe I should cut a big hole in the bonnet and have a roots blower sticking out like Mad Max

yes 021433600

remove belt= no boost

got this and also a bmw aero kit front rear and sides http://www.trademe.co.nz/Browse/Listing.aspx?id=867979192 http://www.trademe.co.nz/motors/car-parts-accessories/bmw/exterior/auction-869648983.htm

got these at bm world 021433600 [email protected]

hi no waste gate setup , just the hose expands a little I suppose ., I think if it was high boost I would have a intercooler . no cert

hi yes my car is still going upto 155k's now so done about 40,000km with the charger . no issues still needs a proper tune though still get good economy etc almost makes as much power as a 3l m3 but pulls much stronger from 3000rpm than a NA engine does whats the charger off , a 2L type one wont push enough air and may just make lots of heat if you crank it up

there where a few specials , just made up for the japan market , basically they where a 635csi auto then fitted with a m88 engine , so no rear mounted battery etc

have alsorts at bm world mtec coupe ones , also after market , koni , etc 021433600

probably a burnt out earth terminal to the light cluster

there was a couple of those lhd japan ones floating around 635csiA converted with m88 engines

http://www.trademe.co.nz/Browse/SearchResults.aspx?searchString=alloys&rptpath=Member_4149413&type=Search&searchType=Member_4149413&generalSearch_keypresses=6&generalSearch_suggested=0&generalSearch_suggestedCategory= http://www.trademe.co.nz/Browse/SearchResults.aspx?searchString=alloys&rptpath=Member_437310&type=Search&searchType=Member_437310&generalSearch_keypresses=6&generalSearch_suggested=0&generalSearch_suggestedCategory=

take all the belts off the front and see if the noise is still there p/s , a/c and alt etc sounds like a bearing etc

any pics etc , from about $3k to $8k??

e24 635csi made into a wagon (hurse)

NICE will it fit into my E30

have these if there is any interest in them http://www.trademe.co.nz/Browse/Listing.aspx?id=863560909 http://www.trademe.co.nz/motors/car-parts-accessories/bmw/exterior/auction-863120787.htm http://www.trademe.co.nz/motors/car-parts-accessories/bmw/exterior/auction-862457694.htm thanks [email protected] 021433600

not quite daily driven (too thirsty ) but my e28 m535i with a 3.65L M88 engine has 527,000km that's equivalent to 1.37 times to the moon and back or 14 times to the Uk and back or 13 times around the earth

needs a bonnet , rad support and front panel , bumper is fine . but if you don't insure your car for enough they will write it off make aure you get agreed value insurance with someone like AA etc otherwise its market value which may have been $3k on this car cost of the panel beaters , painting and parts at stupid retail prices and they will write it off as uneconomical to repair

have quite a few sets at bm world in papakura 021433600

yes will work fine , same box from 316i 318i 318is 318ti 320i 323i 325i etc