Jump to content
_ethrty-Andy_

Official Tools for Hire Thread

Recommended Posts

Does anyone have a reasonable brake bleeder kit I can use for a weekend? Preferably Auckland, can collect.

If I were to get myself a kit, what is the best type? 

Share this post


Link to post
Share on other sites
5 minutes ago, M3AN said:

Does anyone have a reasonable brake bleeder kit I can use for a weekend? Preferably Auckland, can collect.

If I were to get myself a kit, what is the best type? 

Yup, have pneumatic one and lil one way valve job. Prefer the little one way valve job to be fair. Welcome to borrow them. 

Edited by Jacko
  • Thanks 1

Share this post


Link to post
Share on other sites
On 11/21/2020 at 1:21 PM, Jacko said:

Yup, have pneumatic one and lil one way valve job. Prefer the little one way valve job to be fair. Welcome to borrow them. 

Nice. Will PM.

Share this post


Link to post
Share on other sites

Anyone got the pullers and press gear to change the wheel bearings out on a E8/9x? 

Share this post


Link to post
Share on other sites
3 hours ago, Jacko said:

Anyone got the pullers and press gear to change the wheel bearings out on a E8/9x? 

I have a hub puller if that's what you need? @zero might have the bearing tools he lent me?

Hub_Puller.jpg

  • Like 1

Share this post


Link to post
Share on other sites
2 minutes ago, M3AN said:

I have a hub puller if that's what you need? @zero might have the bearing tools he lent me?

Hub_Puller.jpg

Thats the bugger, just need the putting it back together things

Swap ya for brake bleeder kit ;)

  • Like 1

Share this post


Link to post
Share on other sites
3 hours ago, Jacko said:

Thats the bugger, just need the putting it back together things

Swap ya for brake bleeder kit ;)

Done ? when do you need it?

Share this post


Link to post
Share on other sites
11 minutes ago, M3AN said:

Done ? when do you need it?

Was planning on pulling the diff and doing rear end wheel bearings (and parking brake cables) some time over the christmas break

Share this post


Link to post
Share on other sites
1 minute ago, Jacko said:

Was planning on pulling the diff and doing rear end wheel bearings (and parking brake cables) some time over the christmas break

Sweet, probably lines up with my brake swap. Are you planning to come to the December meet?

  • Like 1

Share this post


Link to post
Share on other sites

anyone have an OBD1 reader in akl to help me pull some codes?

Share this post


Link to post
Share on other sites
1 hour ago, qube said:

anyone have an OBD1 reader in akl to help me pull some codes?

OBD1 isn't really a thing but I have a working pre-OBDII (ADS) setup with the pacman connector... which vehicle? 

Edited by M3AN

Share this post


Link to post
Share on other sites
30 minutes ago, qube said:

@M3AN the round thing, 1998 e36 318ti m44

Yep, can do.

Share this post


Link to post
Share on other sites

N52 front main crank seal press tool? Anyone got one? Stuffed my first front main trying to put it in, as careful as I was.

Share this post


Link to post
Share on other sites

Does anyone around Auckland/Hamilton have an engine crane I can borrow for the weekend? Will compensate for the trouble.

Share this post


Link to post
Share on other sites
1 hour ago, Ghost Chip said:

Does anyone around Auckland/Hamilton have an engine crane I can borrow for the weekend? Will compensate for the trouble.

Yes. Auckland Eastern Suburbs. PM me. You'd need a Ute/Pickup or similar and will be a pig to lift...

Share this post


Link to post
Share on other sites
32 minutes ago, HalfJobHarry said:

Yes. Auckland Eastern Suburbs. PM me. You'd need a Ute/Pickup or similar and will be a pig to lift...

🤔 Does anyone have a Ute I can borrow? 😆

Alternatively, will a trailer work? Or a station wagon?

Edited by Ghost Chip

Share this post


Link to post
Share on other sites
19 hours ago, Ghost Chip said:

🤔 Does anyone have a Ute I can borrow? 😆

Alternatively, will a trailer work? Or a station wagon?

A trailer would work, it could lay on its side. it's about 150 - 200 kg 

Share this post


Link to post
Share on other sites

Is there anybody in Wellington (or close by) that would be able to reset an airbag light on my E90? Think I may have fixed the cause of the issue and just need to get the fault code cleared.

 

Can pay in beers or w/e works for you. :)

Share this post


Link to post
Share on other sites

Is there anyone in Auckland with a rotary tool that has a metal disc cutter?

Will compensate for the trouble. Cheers

Share this post


Link to post
Share on other sites
32 minutes ago, Ghost Chip said:

Is there anyone in Auckland with a rotary tool that has a metal disc cutter?

Will compensate for the trouble. Cheers

I have a plug-in Dremel with some good cutting discs... what are you trying to cut (that will determine the number of discs you churn through)?

  • Thanks 1

Share this post


Link to post
Share on other sites
1 hour ago, M3AN said:

I have a plug-in Dremel with some good cutting discs... what are you trying to cut (that will determine the number of discs you churn through)?

This bad boy, just enough so I can get a flat screwdriver to catch. Will buy cutting discs that I chew through

44403BE7-2EEA-4D51-B18A-B22AE6F07F3D.jpeg

Share this post


Link to post
Share on other sites
22 hours ago, Ghost Chip said:

This bad boy, just enough so I can get a flat screwdriver to catch. Will buy cutting discs that I chew through

No problem, I'm in Mount Wellington, send me a PM.

  • Thanks 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...