BM WORLD

may have something to suit . maybe even brand new one. do you have the part number or picture etc

some details here. http://www.bimmersport.co.nz/forums/index....showtopic=31734

another one front view . check out at about 7min 30 sec.

yea seen it done before though i would try it . yea sorry about the quality , the sd card ran out of space in my still camera so that was the last bit i recorded on low quality to just get a bit more track time in. have more higher quality stuff to upload but takes so long. also had a little go pro or someting like that facing forward recording as well , will uplaod some of those later too. higher picture quality but poor sound not sure on the lap times yet , will study the recordings and take times etc. spent a few laps just following mates so they can see footage later etc..

filmed out of the rear screen in my e28 m535i turn up the volume will upload some later

broken wire inside sender drivers side. resolder it back on

3.64 and 3.73 are comon ratios. installed in those you choose what you want i have a 3.91 lsd for one and a 3.25lsd use this to work out your revs at speeds etc http://members.dodo.com.au/~wawawa/revs.htm

look nice and clean oner of these will fix your bumper http://www.trademe.co.nz/motors/car-parts-...n-564382080.htm

worn out air flow meter , vac leaks ,fuel pump had it , faulty fuel pressure regulator

worn out air flow meter , sticky ICV , vac leak . fix these things and they will normally idle nicely

yes go for a single mass flywheel and rebuilt stronger clutch setup. can use a m20 flywheel and starter or one of those after market flywheel clutch kits etc those wheels will work fine

i know where there is a mint set

you still looking have a 93 318is coupe . single airbag car 202k grey , still has reg and wof , just overheated , still drives etc. pretty tidy paint etc. good hood linning . have more pics if needed

has it got spark , pull one coil out plug in a spark plug , crank it over. these engines have issues with crank and cam sensors failing , poor insulation , breaks down from heat etc. easy to test the pump , remove , stick it in a bucket or fuel , hook up 12volts and see if it goes. listen for the sound it makes should be a nice hum , not crackly etc i have brought many cars that have sat for years and the fuel and pumps still work fine etc but i suppose could have got damaged if it was sucking air , they just burn out as they use the fuel to keep the pump cool

gone now will miss that sound oh well onwards and upwards e34 540iT 4.4L 6spd coming soon

about $175 no motor though

cars like 318is and 318ti that use a electric fan only mounted on the back side of the radiator , use the lower temp thermo switch. i use one in my 328i with the S/C so the aux fans cuts in earlier . also in my e28 m5

have genuine new ones http://www.trademe.co.nz/motors/car-parts-...n-562782725.htm $350 for you also can do after market and used ones if you want to go that way cheers brent BM WORLD 021433600

looks nice . do you have the dyno sheet , interested to see the graph etc thanks for posting those up interesting results , nice to see comparrsions on the same dyno etc. camparing the 3.2L high revving engine vs the older style unit heres my rebuilt 3.65L m88 engine http://i145.photobucket.com/albums/r222/br...i/P11401352.jpg build details here http://www.bimmersport.co.nz/forums/index....45&start=45

anyone want a project . 93 318is auto coupe 203k's just got this in guy just drove it up from new plymouth he just got off the motorway and it died. looks like head gasket failure etc has had a new radiator and water pump etc . will still start , but its pressurising the coolant system. still runs and drives etc has reg and wof , needs some other things tidied up like door cards , central locking. window regs etc. has a good hoodlinning ,not sagging. 16" wheels. i have a replacement engine if needed etc. looking at about $1200 as it is. in papakura 021433600

your 5spd conversion http://www.trademe.co.nz/motors/used-cars/...n-562308473.htm i'll take the seats

on trademe now http://www.trademe.co.nz/Browse/Listing.as...198&ed=true

http://www.trademe.co.nz/Browse/Listing.as...078&ed=true

yes will bolt in just the same , as long as you are talking about a m43 engine (cam chain type not the m40 cambelt type) the heads are the same between the 316i and 318i , only the crank is different , same block etc $900 for you

most of the old e28 m535i and e24 635csi used the 390mm types. some m635csi used the bigger 415mm type then when the e34 and e32 came out they went to the 415mm type , pretty rare , pretty horible as far as grip goes. but yes could be worth something if its in good nic and has tread and no cracking in the side walls. but most metric alloys just end up as scrap alloy or to hang your garden hose on and the tyres used for burnouts or growing potatoes out of etc. http://www.trademe.co.nz/motors/car-parts-...n-559599895.htm