BM WORLD

http://www.trademe.co.nz/Browse/Listing.as...075&ed=true 021433600 $150

probably have to change the driveshaft or driveshaft rear end or front flange of the diff to suit your driveshaft but then the diff will need to be set up again

yup

driveshaft coupling is bigger ,axles and drive flanges are bigger and heavier, also not sure what ratio the evo m3 ran . maybe 3.23 etc

yup should be out as much as i can .

yea saw this looks nice just needs this setup . http://www.trademe.co.nz/Browse/Listing.aspx?id=341111081 yea not the best on gas but who cares when you have this much torque and power etc electric reacaro seats nice hamann deep dish wheels mtec body kit , mtec II wheel etc

11,0mm lift 272/272/110 std 262?? i think

auction finishes tuesday 8.30pm comfort model leather seats with switches , air bag sensors ,motors etc http://www.trademe.co.nz/Browse/Listing.aspx?id=340940709

dyno tunning and remapped the ecu on the m5 . http://www.bimmersport.co.nz/forums/index....30&start=30

dyno run today . with the ecu being remaped by gavin at high velocity need to do a bit of work on the intake and exhaust system to let a few more pony's out . a good increase of torque and fairly good across the rev range of power. but its a little restricted up at the topend should keep going past 180rwKw or so previous dyno time with the old worn engine. http://www.bimmersport.co.nz/forums/index....showtopic=25493

got offerd as a trade on my 330i a 2003 st170 focus 2L 6spd manual nz new 195k fsh etc about $10k owns it

finishes tonight . http://www.trademe.co.nz/Browse/Listing.aspx?id=339870863

thats correct .also there are early ones without dimples at the top front edge . can help if needed 021433600

http://www.trademe.co.nz/Browse/Listing.aspx?id=339430192 http://www.trademe.co.nz/Trade-Me-Motors/C...n-341002422.htm www.dension.com

my mate has these http://www.bimmersport.co.nz/forums/index....8&hl=hartge make him an offer

always buy on condition not k's i have seen some pretty ratty cars with less k's than others that have had more love with higher k's

for sale a 4L M60B40 V8 engine with the heads removed . requires 2 new head gasgets and some new big end bearings . and away you go , good for parts or a project . engine was running fine except it has a sleight tapping noise (sounded like a tappet noise) but turned out to be big end bearings on one of the conrods which was causing the piston to just tap the head sleightly. heads where removed for inspection only , they turned out to be fine . $500ono for the engine and most of the bits that go around it . these are rated at 286Hp 210Kw 400Nm just clearing out my shed heads alone would be worth about $700-800 each call 021433600

pic of the block etc

323i are abit slow. better get this one http://www.trademe.co.nz/Trade-Me-Motors/C...n-339870863.htm

just a small update , being enjoying driving this thing around . loads of pull with the 4.4L and 5spd . cleaned it up a bit . will go in soonish for a little paint etc. need to get the ac going for summer . need to get the ecu remapped changed the steering wheel to mtec II type from a early e36 model fitted a pioneer deck with blue tooth handsfree and ipod control etc just swapped the wheels over to some 17" by 8.5" racing dynamics. gotta get some new shocks and lowering springs soon. some nice BBS 15" alloys and tyres for sale .

sorted thanks

just clearing some space in my shed . http://www.trademe.co.nz/Browse/Listing.as...709&ed=true 021433600

same front end as a sedan and similer to a coupe etc. all steering and suspension parts can be swapped around . they are a lighter shell than a sedan.

have this if anone wants to dress up there e28 fits over std chrome bumpers http://www.trademe.co.nz/Browse/Listing.aspx?id=339052841 $400ono 021433600

selling this kit if anyone is after one , 4L v8 M60 engine with 5spd ZF trans from a 95 e38 740i. will include the ecu , afm , wiring loom , trans ecu , ews chip set etc etc . 286HP 210Kw 410Nm quad cam V8 make a great christmas project , shove it in a e30 ,e24 or e28 etc $1500 just making some space in my shed 021433600 second pic is a sample of what it looks like also have another 4L V8 in bits if anyone wants to play around with one , heads are off , needs some big end bearings and new gasgets etc $500ono