Deano

I have a 3.45:1 from a NZ new 320i manual $120Cheers

Have you ever pulled the carpet out? You would hope its only $10 after doing that at pick a part. $100 is cheap if its good.

Yes I have one send me a PM if you still need it

Up for sale renovators dream 1968 1600-2 rolling bare shell..including all the glass and rubbers. A lot of the rust work to the shell completed. Pretty good bonnet quite straight, doors repairable, good boot. Could sell seperate panels, but rather sell the complete shell. Could make an awesome race car project or put back on the road Have most of the car's parts which can be negotiated. I have work to do on the house so its got to go =( Could deliver within the South Island for the price of petrol. http://www.trademe.co.nz/Browse/Listing.aspx?id=319298465 $400

1983 320i E30 coupe rolling shell straight and very tidy has 3 small areas of non structural rust manual rack, 3.45 diff The motor - M20B20 and the factory ZF manual 5 speed have been removed. Good base for a project M52 repower or 2.8L M20, turbo Nissan Rego has expired but due to the age 37 it may be cheaper to re-vin $650

I have one, the distance between the inner holes is 110mm PM me if you want it $30

http://www.m50manifold.com/ Hopefully won't collapse in onitself under vacuum pressure

bump

PMed

PMed

NZ new, 162ks, factory manual, vanos. Sharp looking car. Drives well but needs tidy up inside. Couple of running issues, poss problem with ECU but motor and box great. Have no time to sort out and tidy up and its too good to wreck. Good rubber all round, paint pretty good nice in Alpine White, rear spolier etc. Reg on hold, can put WOF on no probs. No cat or emission gear on it and makes good power for a 2L. Sold the motor so now all parts up for sale. The gearbox is absolutely perfect and the conversion kit comes with everything including freight $1250

Had the codes read..it can be done and had live data. The readings were random and confused..Suspect the ECU so going to try that. Posted WTB ECU

After a ECU 5WK9 002 MS40.1 p/n 1 738 775.9 from NZ new 09/92 320i vanos. I have 5WK9 003 from 95 320i I could swap or cash.

PMed

I can do a ported 731 head to match 885 intake for $260

You can do it with the head in place. The hardest part is getting the rocker shafts to slide out. If you are in Chch I can do it for you...

I can do E30 or E21 M20 flywheel. Possibly have a clutch fork. PM me if you are keen

PMed

Firstly its a 09/92 NZ new 320i vanos factory manual. No CAT or emission control. Its non-EWS and runs 5wk9 002 ECU MS40.1 Can the fault codes be read from the diagnostic connector? A friends "Peak" reader didn't work but ok on his 94 850i and another firm in Chch said the codes cannot be read. Problem is poor acceleration (leaning out i think)when warm. Gradual opening of the throttle (less air) and the car performs near normal. Open the throttle, lots of induction noise, sometimes backfire in the airbox and no power. Perfect from dead cold, and if I plug another temp sensor to trick the ECU to thinking its cold when warm it runs good. Idles perfect, warm or cold. Checked and rechecked for vacuum leaks. So I'm thinking it runs good on the fixed fuel map for cold, when its warm its looking for inputs from the sensors and its not getting one and not giving enough gas. The only thing I haven't tried is a new ECU and MAF. The MAF had been replaced by the previous owner, is the correct one and compared to another 320 when I disconnected the MAF it ran way better than mine so probably not the MAF. I reckon on the ECU. Its been repaired previous due to moisture but the previous owner assured after that it ran good. I have has a hard time trying to find an ECU to try. Any ideas. Should be able to have the fault codes read I would have thought. Also not sure what this (on the right) plugged into..Cable tied to the O2 harness - it looks as though it was plugged into something as its nice and clean but cannot trace any wires to the ECU plug and cant find the colours on the wiring diagram. Thanks

I have a G240 for $265 including freight to Auckland

Thanks for the help..ended up getting it reset at Jade Automotive for $20

Hi..anyone bought or used one of these..any good? http://www.trademe.co.nz/Trade-Me-Motors/C...n-294648868.htm Or anyone in Christchurch able to reset / scan E36 SRS light

Bump

30kgs, 500 x 220 x 200 International Economy Courier More info 2-6 working days $171.83

I'll re-measure and check it again. Any idea what the weight of the head is..I reckoned at 30kgs..I have no scales cause I'm a skinny f....r