musccoo
-
Content Count
259 -
Joined
-
Last visited
Everything posted by musccoo
-
Show us your manifold
-
How much lower do the drop hats make the front? Sent from my HTC One M9 using Tapatalk
-
OK well if parting engine I would be keen thanks Sent from my HTC One M9 using Tapatalk
-
is throttle position sensor 6 pin? Sent from my HTC One M9 using Tapatalk
-
Just been doing some grinding and trying to fit with 6mm of spacers, even then it still doesn't clear and with 5mm spacer the bump would have to be dead flush. I don't understand how the website says 5mm....my euroweaves and these brakes arnt meant to be
-
Pm'd Sent from my HTC One M9 using Tapatalk
-
Thanks David. Yeah I seen this, just found it hard to believe...think 'light grinding' is an understatement haha, but will give it a go this weekend.
-
David you must have different wheels?? as I just measured the clearance from wheel hub to spoke and from disc hub to end of calliper and theres no way it can clear without a spacer. Looks like the minimum I could get away with is a 6mm spacer with grinding down 3mm of the fluid passge
-
I made one out of the old garden pressure sprayer for $15. It seems to work...tis painfully slow coming out of the calliper however... I pump it up to 15psi
-
Really? Yea I have the fancy bracket and line adaptors. I tried to do a test fit and it was hitting the knob when I stacked 5mm of washers on the wheel bolt threads Sent from my HTC One M9 using Tapatalk
-
Anyone run 15x7 et24 euroweaves with rx7 calipers? Tryna figure out what size spacers I need and wondering if I can get away with 5mm + grinding the fluid passage down...10mm spacers would clear but heard bad things about 10mm spacers..
-
Thanks guys I managed by tapping it with a punch to one side to loosen it and get it spinning then was able to use some flat heads. I changed seal then put it back on with some gasket sealer *just in case* Sent from my HTC One M9 using Tapatalk
-
But how do I get it in behind without scratching the head? Sent from my HTC One M9 using Tapatalk
-
So I'm doing my timing belt, water pump etc and want to do the cam seal while I'm there. Ive got the pulley off only problem is I can't get the cam seal housing off. What's the best way to get it off without hacking the head with a screwdriver behind it..? It seems really stuck Thanks
-
Does anyone have an adaptor plate to run a m50 tps on the m20?
-
I used a holden astra linkage merged with the e30 top u joint. No vibration through steering or anything, feels mint
-
Yea think so. Ah Ms2 running wasted spark Sent from my HTC One M9 using Tapatalk
-
Just as long as its the 55 pin one
-
Does anyone have a dead ecu with the 55pin bosch connector? Needing the connector for megasquirt
-
Sorry to thread jack, but has anyone got one of these master cylinders for sale?
-
Ok might give them a call see what they can do. On a side note, put poly transmission mounts in last weekend, cabin sounds hella race car
-
Got any brand recommendations?don't want some heavy as on off thing.. Sent from my HTC One M9 using Tapatalk
-
Stock 3 bar fuel pressure regulator. Took out when I was figuring out fuel issues and put in a brand new one only to find out it was a problem with my pump so this guy is working fine $50
-
So your using like sachs 618 with standard clutch? You don't even need to upgrade to 6 puck? Where did you source the pressure plate? Sent from my HTC One M9 using Tapatalk
-
Is that D1 stage 2 a good setup for m20b25 heading for turbo ~300hp?
