BM WORLD

dont drive with the needle in the red . its cheaper to get a tow truck than a new engine. could caused by a water leak , split radiator ,failed thermostat , failed water pump , failed bearings/fan belt etc. electric fan not working etc etc . best to get it checked by a professional . if you are lucky the head gasget or head may not have cracked depends how long you drove it with the needle in the red?? what area are you in??

so buy the m3 engine off me then i wont have to worry about where i should put it

just make sure the axles go fully back in

i have one availible if you need one now.021433600 and yes Glenn will be there saturday

ok will talk later with you on that one. yes been reading a bit , but most are different set ups to what i have i here.main thing i see is thats its a 94 engine setup into a 1998 car. so will have less going into more??

yes though of that , could use a nz spec 325i 328i rad with the tank on the left , or a jap spec 325i 328i rad with the seperate tank mounted on the right side to the back of the radiator yea thought of that , not a lot of room in the boot of these .maybe 2 small motorbike batterys in each corner pocket not alot of room where the tools are most of the websites are refering to lhd cars

this is the donar car , all panels repaired already (managed to get most panels it needed in teh correct colour) just putting through compliance now. just should be wof'ed and reg by tuesday. and in for some paint on the fornt bumper and front panel and rr quarter next week glen do you see any electrical issues. with m3 cluster fitting , ews ?? , abs lights , asc etc donar m3 is non ews. 1998 318ti auto has ews and asc etc also will need a e30 medium case diff (lsd) axles??rear hub bearings?? is this correct. will e36 m3 rear brakes bolt up to the ti arms? or use 328i rear ones etc?? can i use the m3 rear shocks , but maybe need some other rear springs to get the correct height

not bad 119kw at the wheels . and close to 300Nm

thankswhere to put the battery or the coolant bottle??

ok so M3ti it is then i have a nice 1998 318ti motorsport ready and waiting

yes your wheel will not be centred on the hub .will cause it to wobble al the time. did you get the trust arm bushes checked as they are a heavy car and they wear these out all the time

http://motors.shop.ebay.com/i.html?_nkw=bm...4506.m270.l1313

worn out brake reaction arm (or thrust arm) bush or ball joint or wrapped brake rotors etc part 5 or 6 http://bmwfans.info/parts/catalog/E38/Seda...pport_wishbone/

have this from the 94 m3 black hoodlinning with all the black trims , lights , handles , visors etc from a sunroof coupe model will suit all e36 coupe's with sunrrof hole] $220 s/r http://www.trademe.co.nz/Browse/Listing.aspx?id=379149270 021433600

used trans go for about $500-1500 plus about $300-$500 to fit repairs can be done on them anywhere from $600-6000. have you seen that 540i touring in wellywood nz new 169k $6k or buy ian's manual one.

bump http://www.trademe.co.nz/Browse/Listing.aspx?id=376037460

pics

pic of the m3 seude one

do you come out to papakura i have 4 cars to be done and would be a hassle to drive each one over to the north shore. e36 coupe , e36 touring e34 sedan , e28 sedan

http://www.trademe.co.nz/Browse/Listing.aspx?id=377783144 finishes tonight 7.30pm

just call me if you want to get hold of him 021433600

just putting this up here first before it goes on trade me its my mates runnabout 1992 NZ new e34 525i touring 2.5 m50 non vanos better ZF trans not the jerky jatco. cloth interior (some fraying in front seats) 305k motor runs fine , trans was replaced 1 year ago lower k's than the car. car needs a repaint , clear coat peeling off . hood linning sagging a little 16" bbs alloys . wof reg , non sunroof model so no need to worry about it not working or leaking etc drives nice , smooth and resonably ecnomical. just ready to be turned into something special , fit a 5spd manual, 2.8L m52 or 3L m3 engine etc v8 , v12 , 535i engine , etc etc lower it slam it , tint it etc etc $3k ono

can do speaker covers and maybe seat belt clip thing

reszie your pics to 800 by 600 or upload them to photo bucket etc then link them across

hi . sorry the one i have for sale does not have the cupholder unit $250 for that one