Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation on 07/09/22 in Posts

  1. 7 points
    Thought I would get the ‘inner interior’ all nice before the re-upholstered interior goes back in next week. Shampoo’d the carpets, cabin and boot, repainted most interior plastics and put in some sound deadening (mix of butyl and foam I had in the basement) in the spare wheel well, boot, inner rear quarters / arches and doors while I was at it. Came up well, save a few little coffee stains on passenger side that are ordinarily covered by the seat anyway. Can’t wait to get the new seats, door cards and floor mats in!
  2. 2 points
    Yeah bottom one looks raised\distorted a little on one side but its certainly not bad. Plates may do it over time but a few whacks with some 2x4 and a hammer on that side will flatten that out easy. Then you put the plates in and forget about it.
  3. 2 points
    I should change my to avatar to “ORACLE”
  4. 2 points
    I know of a fairly scungy and dereg manual 325i sedan that sold for 2k locally a few weeks ago. Therefore I will now be offering every e30 owner 5k for their garbage.
  5. 1 point
    Yeah makes sense. Definitely on the shopping list. I also went all Lemförder for the bushes and shock mounts and got limiters for the RTAB's. The driveshaft guibo is the one Meyle HD bit I've got. Today's progress report. Managed to get the headers off in the end, some bolts had better access from underneath. A whole bunch of repetitive strain but off they are, annoyingly tedious process that. Arthritis is fun. Bot manifolds now off as well as the VANOS. Just the camshafts and a few coolant pipes left to tackle tomorrow. Might even have time left to retrofit some steering wheel controls on the daily.
  6. 1 point
  7. 1 point
    bonus, less pricey than dealer retail on the Dunlops. Are you rating them?
  8. 1 point
    @Vass There's *definitely* different springs for 4 and 6 cyl, Sedan, Coupe, Convertible, Touring. Touring rear springs need a bit more beef, and Convertibles a bit more again - counteracting the extra weight. You can get three or four different sizes of spring pads. Mine's on stock springs but one broke; I bought a pair from a wrecker but he sent 4 cyl coupe springs so it was too low at rear. I found a pair with Orange tags (wagon standard) from a knowlegdable user on here, they've been good but have sagged a little, unsurprising as the car is 20 years old now and one assumes the springs are around that age. The big improvement was the Msport ARBs - 24 and 19 (from memory?) and the style 194's - you get 20mm extra track with 245/40R17 at the back over the stock Msport rims... it really flattened it out and way less input from steering wheel for curves at touring speeds. Still you've got those awesome rims, so 18" lushness. I've replaced rear trailing arm bushes, I forget it we did subframe as well. It's not a car you need poly bushes (anywhere) for IMHO. Re springs, @adro reminded me a while ago that Stretten - Mr M539 on youtube - mentioned that Msport equivalent springs he used on Project Cologne (his e46 touring). I think they're reasonably priced sourced from Rock Auto. I think I'd rather have these than my standard go-to H&R Sportsprings. HTH
  9. 1 point
  10. 1 point
    Bit hard to tell from that angle but are the towers flat?. If someone has added reinforcement plates then the strut mounts wont be sitting hard up against the tower. Pin is just for camber adjustment. You want to broken off to adjust camber (usually max neg). Hopefully they weren't trying to compensate for any mushrooming of the towers.
  11. 1 point
  12. 1 point
    Aaaannnyway...she had to get HIGHSPEKt before she leaves😎
  13. 1 point
    http://www.speedhunters.com/2020/06/uniting-nations-the-1930-ford-with-a-v12-german-heart/
  14. 1 point
    Our GS is about to turn in to an LS. Good cars.
  15. 1 point
    Just got done with the wrenching marathon that was changing the oil pan gasket and some other bits on the daily. What an absolute PITA of a job! Kicked it off Sunday morning, finished 1am that day, continued Monday after work until finally having her back on her wheels at 3am... Even with the subframe dropped down, so little space with all the power steering and trans cooler lines in the way. Quite a few hiccups along the way. The most annoying one being getting the dipstick back in. Cleaned up the oil pan, got the new gasket on, RTV'd the joins on the underside, struggled wiggling the pan in place, started it on a few bolts and then spent half an hour trying to get the right angle for the dipstick to slide into the oil pan with no luck, just too much crap in the way on top. Ended up giving up and dropping the sump back down, cleaning everything up and starting over with the dipstick in place. Bloody frustrating game of tetris. Also changed out the valve cover gasket, oil filter housing gasket, engine mounts and alternator. Probably spent half the time cleaning up all the oil that had caked everything up. Not a perfect job but near impossible to get to everything without taking off the intake, which would have gone well beyond the scope of this mission. After a good 4 hours sleep, set off for work in the morning. Car started up fine but got the ABS and brake lights go off on the dash, as they sometimes do with the wheels off the ground for a while. Drove out onto the street, parked up and tried turning the car off and on only for it not to start again... Flat battery. Ran back home to grab the spare, got her running but from the voltage saw that the alternator wasn't kicking in. Figured the new one must have been faulty. Dammit. Pulled into the driveway and started pulling the intake back apart to put the old noisy one back in, only to discover I'd forgotten to plug the alternator cable back in... Classic 3am brain fog. Hopelessly late, finally set off for work only to hear a clunking noise coming from the front. It then hit me I'd also forgotten to tighten the wheel nuts after I'd dropped the car down from the jack stands... Bloody hell After catching up on lost sleep, tidied up some of the loose ends today so hopefully that's the end of my oil leak dramas for a wee while at least. Thank f**k that's over and done with.
  16. 1 point
  17. 1 point
    The latest update is I have purchased a fibreglass Sun Roof panel, will get it painted, fitted & replace the seal The existing panel, has rust, as per normal, the only rust in the car, never again, fibreglass rules
×
×
  • Create New...