Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation on 12/23/22 in Posts

  1. 2 points
    And this is where I’m currently at, -engine mounted -gearbox mounted -driveshaft made -all exhaust/turbo made to downpipe -fuel pump mounted, new fuel lines made and plumbed -radiator mounted and plumbed -intercooler mounted and piping fabricated -wiring all hooked up-minus afew sensors -BC Coilovers welded up I will make more of an effort to take more photos and post more of my progress if there is any interest. ive still got loads of work to get this done and would appreciate any advice/help.
  2. 1 point
    No, different seller. This has always been a Christchurch car. The other Auckland guy bought both the black S54 and the silver 16000km S50 car from HellBM. There is a strong interelationship with this blue car, and the silver Hell BM car in that both were imported damaged, and LHD. The Christchurch car came alongside a 3 litre E36/7 coupe, also damaged, this and new parts purchased in NZ saw the estoril car completed, complied and RHD, the tub and any bits left over went to Auckland, where some of those bits went into the repair and conversion of the silver car.
  3. 1 point
    Its an all wheel drive hybrid, very on point!!
  4. 1 point
    Not everyday you see one of these
  5. 1 point
    Reviewing what is left to do on the car to refresh items that haven't been in my care, the main points are; - cooling system (except Radiator, which was replaced 18 months ago) - Vanos service/rebuild (got the big x8r kit) - PCV system - water pump - thermostat - water pump pulley - various temp sensors - related gaskets - fan clutch So as it 'tis the season I've ordered bits or bits have just been delivered for all of the above, thanks Santa
  6. 1 point
    Yeah. Nah. My eyes still hurt! 🤣 probably the rare time we will agree to disagree on this one haha
  7. 1 point
  8. 1 point
    It's not too bad. Saw it on the dealer parked. Aside from the shape of the wheel arch covers it seems to be ok.
  9. 1 point
    Clearly a trader as the RS4 is a fresh import and un-reg. IIRC all their listings, including the M roadster got pulled last time round.
  10. 1 point
    Red alert ! "Selling my absolutely beautiful BMW M Coupe!" And your 2005 Toyota RunX, your Mitsubishi, your Audi RS4, your Kawasaki...? Possible, that's a lot of vehicles for a 'Private seller' to have listed at once.
  11. 1 point
    bimmer.work says allotted VIN LHD Euro-spec (CM91) for Japan. ad is definitely misleading
  12. 1 point
    Carjam confirms (says?) imported from Japan.
  13. 1 point
    Definitely a LHD shell…tire pressure sticker on the wrong side. Guessing it was a US chassis as no VIN sticker on the sill either
  14. 1 point
    Watched some kid and his brother in daddies new Ranger trying to Stevie Wonder their way around the Supercheap carpark this morning. Cameras and sensors on every corner, all the gear an no idea.
  15. 1 point
    Last week I had the lights protected by Obsessive Car Detailing in Auckland. Great team and you can't see the film unless you're really, really looking. I installed the headlights last Sunday afternoon (11 December) after the 24 hours waiting time for the protectant film to fully set in place. They look amazing both off and on. the Auto levelling works as it should and they are adjusted pretty well but will need some fine-tuning at some stage to ensure the aim is in spec. After a short drive in the rain on Sunday, I noted some very light condensation in the left-hand side. This dissipated pretty quickly but was concerning as it meant the seal wasn't weather-tight. I decided to remove the light, separate it again, and reseal it from scratch. Upon removal, I could see I hadn't been liberal enough with the sealant on this light and it had rolled rather than bulged when I had pushed the lens home. ( I've also read that Xenon and LED units don't get as hot as Halogens, so won't evaporate moisture to the same level. The sealant was heated up in small sections and scraped out using a plastic trim tool. An all-new more liberal bead of sealant was laid in the channel and the light reassembled. The light is back in the car now and working great, fingers are crossed that the condensation doesn't return as I don't fancy pulling it apart again This closes the lighting chapter in project E39.
  16. 1 point
    Super clean E34 manual 525xi touring. Sub 100k km according to carjam and Oxford green over beige leather 😍
  17. 1 point
    As per the trade me add, I sold my 4.8is and these are surplus to requirement and could be of interest to other e53 owner. There is an extra set of rears which I had reconditioned and were never used so you could have a 10.5 inch square set up or choose to staggered. Priced at $1000. https://www.trademe.co.nz/trade-me-motors/car-parts-accessories/wheels-tyres/alloy-wheels/auction-3901319793.htm
  18. 1 point
    I'll get some video at some point once certified and fully road legal, its fairly fun as it is but suspect it will be even more so when you can drive it hard and bang through some gears etc. Went in for cert yesterday and came away with 13 things to address, only a couple that will need some thinking about ... mostly tidy-up items like heat proofing a brake line, some receipts for various bits, get a wheel alignment etc. Also, wheel bolts were 0.75 turns too short ... thats 1.1mm from memory 😂 Luckily found some UK made items from Racerproducts yuuuusssss. Hoping to get in for WoF recheck within the 28 day period but unsure if i can get all the cert items finished by then to be honest. In other progress, got the UpRev 'tuner' cable today so can try to address the wacky idle issues (noted for cert unfortunately, rats). Should be fun to do some proper data logging at last !! Also got in on the HPA Black Friday sales and got the tuner starter course for 50% off which is pretty sweet. Couple of shots from today, the lads at my tyre guys (JP Tyres, Glenfield AKL) were pretty interested and commented on how it looks beneath ... first time i have seen its belly on a hoist after starting at it from 30cm on my back for 2 years !! Still need to get some better shots before i drive it more.
  19. 1 point
    E36 Coupe in profile has such perfect proportions
  20. 1 point
    Also, major development on the engine output front !! Had been feeling like it was no where near as potent as it was lately although it was driving much better (idle, rev hang etc). Have been trying to data log my a/f ratios or voltages via Android app NCSIII and OBD2 dongle but alas they only have readings in 'alpha' ... this was on the thought that my sensors are much further back in the exhaust than previous and may not be getting hot enough etc, hence skewing things. Annnnnnnyyyhoooooo ... via the phone app I could at least reset the fuel trims, so I did that. Idle and drivability back to been a bit pants BUT it must have picked up 100hp !! Back to ripping like it used to. So will have to get it on a dyno with some calibrated wide band and see what the story is some time soon ... great that I was not imagining it slowing up at least !! Now, these may look essentially like the same photos but ... they're not 😆 Did a ceramic spray coating, dressed the tyres and finally cleaned under the bonnet. Its probably looking about as good as its going to for a while !!
  21. 1 point
    Yuuur not sure, I assume they put them in place pretty accurately ... I should have made a little jig to test them out hmmmm. When my new Powerflex bushes arrive i'll try and remember to check it out 👍 Made up the remaining lower bracket for the dry sump tank which is adding some piece of mind, although it was very secure with just the top mount installed. Replaced all of the shocks with the near new items I got from @Eagle, which is great as it has a go at a WoF today (essentially generation of another todo list probably hah). Drivers airbag was replaced this morning at BMW under recall but alas did not clear down the code there Will start a thread for that as will need to get it resolved. Completed the custom pool noodle intake tubes, could have spent longer getting them looking perfectly round / smooth but compromised to get things moving. Got a custom can of 2k clear satin to finish them up but ended up with a lot of pinholes for some reason. Still look ok, just don't inspect closely !! Finally got the air filters installed which is pretty exciting ... had to change out to some compact models as the original cheap pod's I got were never going to fit once the guard liners were in place.
  22. 1 point
    Got the sway bay back from Archers Auto Springs, paint job is a bit industrial (expected) but looks accurate to my mockup. Had it made with three holes per side with the middle being the OEM location. Mounts up fine and is a really great fit Stoked !! Pretty cost effective also at only $405.
×
×
  • Create New...