e30ftw

I read about that but I had gone the weekend before that and didn't plan on going again. Andy lives closer..

Still looks damn good.

Lol i tipped off Andy and he honed in like a vulture

Just 12point metric normally? Pictures?

I remember this, haven't seen it in a few years. That is some nasty rust though, bet it's throughout

Nice wheels, Are they 3 Piece? Going for bigger lips?

Looking for an oil cooler with lines from an M3. Or an oil cooler adapter to -10an fittings.

How did you end up with needing the U.S stuff? Couldn't Kassel do Euro software / Euro wiring on the adapter loom and use a regular relay?

Yeah I went and had a look at this, There's a heck of a lot of rust on it, You haven't seen the start of it if you only just noticed this! Why else did ya think no one local bought it

Anyone after a new Clutch reservoir cap? Pretty common to be cracked these things. Bought a reservoir and cap separately and didn't realize the reservoir comes with one anyway. $15 shipped? Can include a reservoir too, But it ain't new.

I reckon M52B28 is the best for a budget and it's real straight forward. Lightweight, plenty of power and .they are quite easy to get power out of with M54 3L internals and intake / cams / headers.

Yup, have them already probably a couple pages back. Just need one more section of the loom and then figuring out where everything goes and I can put everything back in. Hopefully have it going in the next few weeks, Just more and more things that need doing. Change one thing then down the line something else needs to be done, then something else. Where did you guys place your Driveshaft loops?

Sent my LSD up to Kayne B to rebuild and add extra friction plates. Wish I had a before photo, The diff was originally from a near 400,000km M325i, then spent 2 years in my touring. Was covered in oil, completely dirty and I wasn't really sure it had any lock up left in it. Looks brand new now. Very impressed. Big thanks to Hans for getting it up there and back for me. Have one part of the loom left which should hopefully arrive tomorrow. I've been blown away how much work is involved in doing this, I definitely underestimated it but I'm in too deep now haha. The wiring is just crazy, bits all over the place. Once I get that final loom all the air intake side can finally go on.

Good luck doing only trail arms, I'd do the whole lot in one shot. Absolute c*nt of a job, I rate it worse than doing engine or gearbox swaps.

Only the shocks left now. And I know, I didn't want to part with them they are very good. They just don't work with my current setup unfortunately.

You can only buy in 20L. Talk to Kayne Barrie, he does it for 39.99 /L plus GST.

Not sure but I doubt it, rear end is totally different to E30s

Yeah I know what you mean, But I don't think H&R had 4cyl / 6cyl springs. They list as compatible with both but with less of a drop on m3/318i. This is how they sat with an m20.

Yeah, Just hadn't taken the rears out when I took the photos. Yes I don't think H&R do any different between the two. About 10 - 15mm. Enough to close up a gap. I was using them because my front raised slightly when I went from M20 to M52 (due to being lighter).

All sold.

Interested in some H&R springs? Full set 280$ shipped

I don't get why you would be against a cold air box, all it means is you are shielding the air intake from the warm engine bay air so it's drawing air through the grills or whet ever, which is colder. Being boxed in can amplify the induction sound too so why not? It's just pointless when you remove the OEM airbox which has a closed in filter, and a tube to get air from behind the headlights. They did it like that for a reason.

I am looking for the section of loom that sits ontop of the valve cover on the exhaust side of the coil packs. I either need to find the correct part number if someone has it, or the loom itself if someone by any chance has one... This part of the loom is where the O2 sensors for the S54 come up to the valve cover and plug into. I think it also has reverse light wiring on a manual and maybe integrated with more on an SMG? Again, I can't find anything worth while. Here is a picture from google when looking for "MN3 oxygen sensor harness" if anyone can help with one or the correct part number. I have tried Real OEM.

I've had a 55" for a couple years, Feel like it's way too small. Grew up with a mint 21" CRT in the dining room and the splash out in the lounge with a 29" CRT

I sold one earlier this year for $220. But in saying that I bought another of TradeMe as a spare for $120, so you can get lucky.