e30ftw

Yeah I started doing that, Sat there for like 10 minutes with a gas torch, seems like a painfully slow of doing it else I would

Anyone in the Wellington area want to get some bushes out for me? Will pay for your time. Everything is out, I just need to get the subframe and bushes out. Bonus if you feel like doing wheel bearings too.

Nah I've looked, need's to be specifically Evo linkage for a 6 speed m3. 25112227893 - Shift carrier 25112228055 - Shift rod

Bump. NLA from BMW ffs.

Nah no axles, yeah the brakes should be the same.

A TradeMe auction? Are we that bad?

Bump. Added a couple things.

^I hate when you flat with people who put like 2 plates a cup and one f**king spoon and turn the dishwasher on a heavy cycle.

End result looks pretty good, something different

Yes same applies, all the m5x engines have basically the same blocks, so the mounts, sump and gearbox options are the same as m50/m52. M54 gets harder with a more complicated ECU, wiring and things like electronic throttle. There are many ways around it (OBD1 swap). Good luck

NOW ON TRADEME $1 RESERVE! Bump. Have alot of it on Trademe @ $1 ending tomorrow night! M52 cams http://www.trademe.co.nz/Browse/Listing.aspx?id=932524570 Bosch 413 red label DME http://www.trademe.co.nz/Browse/Listing.aspx?id=932524589 Brake Master Cylinder http://www.trademe.co.nz/Browse/Listing.aspx?id=932524573 Bosch 405 DME http://www.trademe.co.nz/Browse/Listing.aspx?id=932524592 E30 Slave http://www.trademe.co.nz/Browse/Listing.aspx?id=932535623 E46 M3 dual mass flywheel http://www.trademe.co.nz/Browse/Listing.aspx?id=932685551 Need to get rid of some of the stuff I have lying around, I'll try get pics but sh*t is all over the show atm. E30 Brake Master Cylinder - Good condition, $40 E30 325i Front Calipers, Can include discs, pads still have meat on them. $60 e30 touring rear sway bar with poly bushes - $60 e30 complete disc rear end 320i - $60 Brakes, arms, axles and subframe e30 steering rack - $50 e36 328i radiator- $40 M52b28 cams. Removed when i swapped to s52 cams. Good condition. $60 M52B28 MAF - $60 NEW M52/M50 front Vanos unit gasket (Between head and vanos unit) P/N 11361740840 $15 Bosch 405 (M50B25 NV) - $60 Bosch 413 Red label (M50B25 Vanos) - $80 M50 Intake boot, Single hole (e36?) Good condition, $25

This basically covers off everything you need. http://www.e30zone.net/e30zonewiki/index.php/Engine_Swap_-_M5x

You need a E34 M50 sump and oil pick, Not M20.

Don't worry don't need one now doing something else.

I used this when I had an m52 with 240 gearbox /m20 flywheel, http://www.trademe.co.nz/motors/car-parts-accessories/bmw/clutches/auction-917971060.htm Uses a Sachs pressure plate. Can't remember what the clutch disc was. Pedal is slightly harder than stock but it's a real good clutch. Took about 1000-1500kms to wear in though, used to make the car shudder when disengaging the clutch in 1st or when trying to reverse, so you need to drive it nicely for a while.

I have a M50b25 one if needed and local. You can tell the difference by looking at the gaps between runners, the square holes should fit directly between each runner, if there is some gap between then it's the thinner 2.0 runners. Check ID photos here; http://www.e30zone.net/e30zonewiki/index.php/M5x_Inlet

Looking for a brake booster for a 2002Tii Help

That touring will have far more rust than just surface rust. There is no such thing as surface rust with an e30 these days, especially spots 1,2 and 3 they are very common spots to rust right through. If you can see it on the surface it's too late. If you plan on looking at it, check under the battery tray, and down the firewall under the tray. I'm guessing it has spent alot of it's life outside. Also "second hand tyres"... shows how well and how willing the owner is for maintanence.

The Nzd to USD at the moment. Bloody hell!

Anyone have a shift rod and carrier for a E36 M3 Evo? Trying to avoid buying new.

Looks like someone has added it all on. Bumper trims have been painted red and the eyelids are aftermarket. *Edit* Oh wait I forget, Bumpers are normallly black. They have been painted red, including the rubber trims. Keep thinking bumpers are colour matched from factory, but that's just SE's.

So timing marks line up, Engine turns over, I doubt it's a valve to piston. Was the engine a runner before you put it in? Who did you take it to anyway?

I did ask earlier, Did you try to turn it over using a wrench on the front to see if it was stuck?

I don't get why you need the kit in the first place. I ran the m50 manifold, m50 TB, e36 Intake boot with 2 bungs, One I fit the IAT sensor into and the other one I fitted the m50 ICV lines but used the m52 ICV. Put a T into it with a tube for the Crank case.

Interesting. Which year / model?